background image

TABLE OF CONTENTS

PRODUCT SAFETY

1

SPECIFICATIONS

2

PREPARATION

UNPACKING

2

OIL REQUIREMENTS

2

FUEL REQUIREMENTS

2

COOLANT REQUIREMENTS

3

BATTERY CONNECTIONS

3

CONTROL PANEL LAYOUT & DESCRIPTION

DGC-2020 ENGINE CONTROL

4

FRONT PANEL DESCRIPTION

6

RECEPTACLE AND BREAKERS

7

FULL POWER CONNECTIONS

8

OPERATIONS

SELECTING THE CORRECT

VOLTAGE

8

START-UP CHECKLIST

9

ELECTRIC STARTING

9

REMOTE STARTING

9

CONNECTING THE LOADS

10

UNIT STORAGE

11

50 CYCLE OPERATION

11

MAINTENANCE

11

PREVENTIVE  MAINTENANCE

11

WIRING DIAGRAMS

DC ELECTRICAL SCHEMATIC

12

SHORE POWER

13

GENERATOR  WIRING

14

SELECTOR SWITCH WIRING

15

CIRCUIT BREAKER WIRING

16

RECEPTACLE PANEL

17

WARRANTY

18

SAVE THESE INSTRUCTION

This manual contains important instructions that
should be followed during installation and mainte-
nance of the generator and batteries.

Read and understand all instructions in the manual
before starting and operating the generator set.

USING THIS MANUAL

Congratulations on your choice of a Winco generator set.
You have selected a high-quality, precision-engineered
generator set designed and tested to give you years of
satisfactory portable service.

To get the best performance from your new engine
generator set, it is important that you carefully read and
follow the operating instructions in this manual.

Should you experience a problem please follow the
“Things To Check” near the end of this manual. The
warranty listed in this manual describes what you can
expect from WINCO should you need service assistance
in the future.

PROPER USE AND INSTALLATION

You must be sure your new engine generator set is:
*

Properly serviced before starting

*

Operated in a well ventilated area

*

Exhaust gases are dispersed safely

*

Wired by a qualified electrician

*

Operated only for its designed purposes

*

Used only by operators who understand its operation

*

Properly maintained

COPY YOUR MODEL AND SERIAL NUMBER
BELOW FOR FUTURE REFERENCE.

No other WINCO generator has the same serial number
as yours.  It is important that you record the number and
other vital information here, if you should ever need to
contact us on this unit it will help us to respond to your
needs faster.

MODEL____________________________________

SERIAL  NUMBER____________________________

PURCHASE  DATE____________________________

DEALER___________________________________

Page i

Содержание REDI POWER RP 55





















Отзывы: