31
OPM-143/G
US ENVIRONMENTAL WARRANTY STATEMENT
FPT Industrial S.p.A. warrants to the ultimate purchaser and each subsequent purchaser that the engine is designed, built, and equipped
so as to conform with US Environmental Protection Agency (EPA) regulations applicable at the time of manufacture and that it is free
from defects in workmanship or material which would cause it not to meet these regulations for a period of time:
2 years or 1,500 hours of operation, whichever occurs first, for engines less than 19kW (25HP)
5 Years or 3,000 hours of operation, whichever occurs first, for engines greater than or equal to 19kW (25 HP)
Note: This warranty applies to all units operated in the United States and Canada.
COVERAGE:
The model year, class of engine, and emission application determination for your engine are identified on the Emission Control
Information Label. This label is affixed to one of the following areas of the engine: the top of the engine’s rocker arm cover, the right-
hand side of the oil pan, and the right-hand side of the engine’s front gear cover. The warranty period begins on the date the new
equipment is sold to the first retail purchaser. The presence of the emission control label is the indication that the engine conforms to
the applicable standards. Any emission control system parts which are proven defective during normal use will be repaired or replaced
during the warranty period.
The engine owner has responsibility to perform all the required maintenance listed in the Owner’s Manual. FPT Industrial S.p.A. will not
deny an emission warranty claim solely because no record of maintenance exists; however, a claim may be denied if failure to perform
maintenance resulted in the failure of the warranty part.
It is recommended that replacement parts used for maintenance or repairs be FPT Industrial S.p.A. service parats to maintain the quality
originally designed into your emission certified engine. The use of non-FPT Industrial S.p.A. parts does not invalidate the warranty on
other components unless the use of such parts causes damage to warrantied parts.
The manufacturer is liable for damages to the other engine components caused by the failure of any warranted emission control system
part. FPT Industrial S.p.A. is not responsible for failures resulting from improper repair or the use of parts that are not genuine FPT
Industrial S.p.A. or FPT Industrial S.p.A. approved parts.
COMPONENT COVERAGE:
New engines certified for sale and registered will have the following items covered by the emission warranty, depending on the
emission level of the engine, if the items were first installed on the new engine as original equipment.
Fuel injection system
Fuel injection part
Fuel injectors
Fuel injection lines
Air induction system
Intake manifold
Turbocharger system (includes exhaust manifold)
Charger air cooler
Positive Crankcase Ventilation (PCV) system
(if
applicable)
PCV valve
Oil cap filler
Exhaust after treatment devices (if applicable)
Diesel Oxidation Catalyst (DOC)
Diesel Particulate Filter (DPF)
Selective Catalytic Reduction (SCR)
Diesel Exhaust Fluid (DEF) tank and dispensing systems
REVALIDATION OF WARRANTY
FOR LONG-TERM STORAGE OF ENGINES
These procedures are intended to prevent oxidation and/or fatigue of internal engine and fuel injection equipment components. If
any engine has not been sold to the end user prior to nine (9) months after the manufactured build date of the engine, the seller must
revalidate each engine at this time, and every twelve (12) months afterwards for a maximum of twenty-four (24) months for warranty
coverage to be available, and provide written confirmation to WINCO inc that the engine was revalidated. Warranty will be exhausted if
the unit is still in the seller’s inventory after revalidation cycle.
1. Carefully inspect all external components for damage and/or corrosion
2. Rotate the engine approximately five (5) revolutions to prevent fatigue of internal engine components.
3. The engine must be protected from moisture intrusion and/or growth.
4. Circulate diesel fuel or fuel injection equipment calibration oil through the fuel injection equipment system components, and
ensure the fuel system remains sealed to prevent evaporation and/or contamination.
5. Fill the cooling system with coolant. If not installed in an application, the cooling system connections at the thermostat housing
and the water pump must remain dry and closed to limit environmental exposure and/or corrosion.
6. The engine must be pre-oiled before start-up (see lubrication section for lubrication specifications. This involves cranking the
engine for one (1) minute at 10 second crank/10 second no crank intervals, while ensuring the engine will not start, in order to
circulate oil throughout the lubrication and turbo systems without damaging the starter motor.
7. If the engine is installed in an application, “fogging” the engine is an acceptable method to protect the internal engine
components by operating the engine for 15minutes at 500-800 RPM, and nebulize the following amounts of oil through the air
intake system.
CAUTION: Exceeding the oil increments below may induce engine damage.
3-4 cylinder engines and per bank (8 cylinder engines)
60 grams
6
cylinder
engines
120
grams
12 cylinder engines (per bank)
80 grams
Service records indicating the requirements are performed must be maintained. Failure to comply with these storage requirement
procedures may revoke consignment privileges, and limit and/or void the applicable warranty on the engine.
Содержание DE50F4-XX/1
Страница 27: ...27 OPM 143 G ENGINE HARNESS ...
