background image

32

OPM-143/G

WINCO Inc. has been engineering and manufacturing high quality generators since 1927. WINCO Inc. warrants to the original owner that the purchased 
product is free from defects in materials and/or workmanship for the period of time outlined below. If the product should prove defective within the time period 
outlined below, it will be repaired, adjusted or replaced at the option of WINCO Inc., provided that the product, upon inspection by an authorized WINCO Inc. 
service center, has been found to have been properly installed, maintained and operated in accordance with WINCO Inc.’s Installation and Operating Manuals, 
engine manufacturer installation and operation guidelines, and National and local code. This limited warranty is not valid or enforceable unless:
 

1. All supporting product maintenance records are kept on file and made available upon request from WINCO Inc. 

 

2. A copy of the WINCO Inc. Start-up Completion and Warranty Validation Checklist is properly and completely filled out and returned to 

 

  WINCO Inc. within 30 days of start-up. 

 

3. The product is routinely exercised in accordance with operating instructions. This warranty does not apply to malfunctions caused by 

 

  physical damage, misuse, improper installation, repair or service by unauthorized persons; or normal wear and tear. The warranty is 

 

  not assignable.

WINCO Inc. Product Warranty Period:
 

• Engine generator set: Parts and Labor for one (1) year from the date of factory invoice or 2,000 hours (whichever occurs first).

 

• Accessories (installed on the product or shipped loose): Parts and Labor for one (1) year from the date of factory invoice or 2,000 hours 

 

  (whichever occurs first).

 

The start of the warranty period can be adjusted to the date of unit start-up (limited up to 180 days from invoice date) provided that the  

 

following information is provided to WINCO Inc. at the time of start-up: 

 

  1. A copy of the WINCO Inc. Start-up Completion and Warranty Validation Checklist is properly and completely filled out and returned to 

 

    WINCO Inc. within 30 days of start-up. 

 

  2. Some engines may require revalidation after long-term storage. The engine revalidation process if included in the manual must be 

 

  followed.

To obtain warranty service: 
 

Contact your nearest authorized WINCO Inc. service center. For assistance in locating your nearest authorized service center, contact WINCO 

 

Inc.’s Service Department.

Warranty service may be performed by an authorized WINCO Inc. service center only. Service work performed by unauthorized persons will void all warranties.

WINCO Inc. shall not be liable for any claim in an amount greater than the purchase price of the product. In no event shall WINCO Inc. be held liable for any 
special, indirect, consequential or liquidated damages.

WINCO Inc. shall not be liable for any claim that requires replacement of engine, part, or component of the product that is no longer manufactured or available. 
Additionally, WINCO Inc. will not be liable for any engine replacement that may require an emissions tier-level change.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE DESCRIBED HEREIN. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, OR 
OTHERWISE CREATED UNDER THE UNIFORM COMMERCIAL CODE, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, OR WARRANTIES 
OF FITNESS FOR A PARTICULAR PURPOSE.

The following items and/or circumstances are excluded from this limited warranty:
 

• Engine starting batteries: The battery manufacturers’ warranty applies. Consult your local battery supplier for warranty service. 

 

• Fuel system and/or governing system adjustments performed during or after start-up.

 

• Normal maintenance items: Consumable items such as belts, filters and hoses.

 

• Damage caused by over-loading the generator and failure to adequately provide over-load protection.

 

• LP/NG fuel adjustments or conversion from one fuel to another.

 

• Any repeat or shop come-back repairs resulting from poor service work or improper diagnosis and testing. Replacement of parts as a trail-and-error 

 

  method of diagnosis will not be considered for warranty.

 

• Adjustments and tune–ups performed during start-up or thereafter. 

 

• Loose connections (electrical and mechanical) not found during start-up.

 

• All fluid level related items including low coolant not found during start-up or checked during regular maintenance intervals. 

 

• Equipment modifications made without the written consent of WINCO Inc. will void all warranties.

 

• Shipping damage of any type. All equipment is shipped F.O.B. factory and risk of loss transfers to the carrier once loaded for shipment. It is the 

 

  responsibility of the receiving party to sign for the receipt of, and note any shipping damage to the equipment. Freight damage claim filing is the 

 

  responsibility of the receiving party. In the rare event that damage occurs during shipment, WINCO Inc. will not warrant any damage to the unit 

 

  resulting from packaging material.

 

• Any special access fees, requirements or after hours scheduling to gain access to the equipment for warranty service purposes. 

 

• Rental generators used while warranty work is being performed.

 

• Damages caused by acts of nature, such as lightning, wind, flood, wild fires, or earthquake.

 

• Any damage due to situations beyond the control of the manufacturing and/or workmanship of the product. 

 

• Use of non-protected steel enclosure within 25 miles of the coast.

 

• Damage caused by improper installation or failure to provide adequate ventilation.

 

• Misapplication of the equipment such as usage outside the original design parameters as stated on the nameplate of the equipment. 

 

• Equipment purchased at the standby rating that is being used in a prime power application(s).

 

• Diesel engine “Wet Stacking” due to lightly loaded diesel engines.

 

• Travel time or service calls unless given written authorization by WINCO Inc.

ENGINE GENERATOR SET 

ONE (1) YEAR, 2,000 HOUR PRIME 

LIMITED WARRANTY

WINCO INC. • 225 S. CORDOVA AVE • LE CENTER, MN  56057 • 507-357-6821

Содержание DE50F4-XX/1

































Отзывы: