Wilson Electronics 271265 Скачать руководство пользователя страница 19

Страница: 19 / 20

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Operation is subject to the following two conditions: (1) This

device may not cause interference and (2) this device must accept

any interference, including interference that may cause undesired

operation of this device .

Disclaimer: The information provided by Wilson Electronics,

Inc . is believed to be complete and accurate . However, no

responsibility is assumed by Wilson Electronics, Inc . for any

business or personal losses arising from its use, or for any

infringements of patents or other rights of third parties that

may result from its use .

One or more of the following U .S . Patent numbers may apply

to the Signal Booster in this product – D596,614; D596,615;

D563,381;7,729,669; 7,486,929; 7,729,656; 7,409,186; 7,783,318;

7,684,838; 12,714,994 .

Содержание 271265





















Результаты поиска

Содержание 271265

Отзывы:

Wilson Electronics 271265, Руководство по установке, Страница: 19 / 20

Результаты поиска

Содержание 271265

Отзывы: