Wilson Electronics 271265 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 20

Wilson Electronics 271265 Скачать руководство пользователя страница 12

11

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

12

Powering up a Wilson Electronics Signal Booster

Never point the front of a directional outside antenna toward the

1 .

inside antenna . See Figure 2 on page 12 .

Ensure that both the outside antenna coax cable and the inside

2 .

antenna coax cable are connected to the signal booster

and the

connections are tight

before powering up the signal booster .

Plug the 6-volt power supply into the signal booster input

3 .

marked “POWER” (carefully, to avoid damaging the center pin)

and then into a wall outlet .

If the signal booster does not have a green light, please see

4 .

pages 13 & 14 .

If you know that only one frequency band (800 or 1900) is

5 .

available in your coverage area (or going to be used), reduce

the gain control on the frequency band that is NOT in use to the

lowest setting . This will reduce the power consumption of the

signal booster .

Using multiple signal boosters in one installation may cause

6 .

interference to the cell tower .

Contact Wilson Electronics Technical Support Team with any

7 .

questions at 866-294-1660 or email tech@wilsonelectronics .com .

Technical Support hours are 7 am to 6 pm MST .

DB Pro™

«
...
10
11
12
13
14
...
»

Содержание 271265





















Отзывы:

Нет отзывов