background image

D

EG - Konformitätserklärung

GB 

EC – Declaration of conformity 

F

Déclaration de conformité CEE 

Hiermit erklären wir, dass die Bauarten der Baureihe : 

MVIE 1ph

Herewith, we declare that this product:

MHIE 1ph 

Par le présent, nous déclarons que cet agrégat : 

in der gelieferten Ausführung folgenden einschlägigen Bestimmungen entspricht: 

in its delivered state comply with the following relevant provisions: 
est conforme aux dispositions suivants dont il relève: 

EG-Maschinenrichtlinie 98/37/EG 
EC-Machinery directive 
Directives CEE relatives aux machines 

Elektromagnetische Verträglichkeit - Richtlinie 

2004/1008/EG 

Electromagnetic compatibility - directive 
Compatibilité électromagnétique- directive 

Niederspannungsrichtlinie 2006/95/EG 
Low voltage directive 
Direction basse-tension 

Angewendete harmonisierte Normen, insbesondere:

EN 809

Applied harmonized standards, in particular: 

EN 60204-1

Normes harmonisées, notamment: 

EN 61800-3

Bei einer mit uns nicht abgestimmten technischen Änderung der oben genannten Bauarten, verliert diese Erklärung ihre Gültigkeit. 
If the above mentioned series are technically modified without our approval, this declaration shall no longer be applicable. 
Si les gammes mentionnées ci-dessus sont modifiées sans notre approbation, cette déclaration perdra sa validité. 

Dortmund, 05.09.2008 

Erwin Prieß 

Quality Manager 

WILO SE 
Nortkirchenstraße 100 

44263 Dortmund 

Document: 2089935.2 

Содержание MHIE 1ph






















Отзывы: