Wilo Atmos GIGA-B Скачать руководство пользователя страница 40

Страница: 40 / 68

Safety

WILO SE 2022-06

2.5

Installing/dismantling

Wear protective equipment:

–

Safety shoes

–

Safety gloves for protection against cuts

–

Safety helmet (when using lifting equipment)

Locally applicable laws and regulations on work safety and accident prevention
must be complied with.

The procedure described in the installation and operating instructions for shutting
down the product/unit must be strictly observed.

Disconnect the device from the mains and secure it against being switched on
again without authorisation.

All rotating parts must be at a standstill.

Close the gate valve in the inlet and in the pressure pipe.

Provide adequate aeration in enclosed spaces.

Make sure that there is no risk of explosion when carrying out any type of welding
work or work with electrical devices.

2.6

During operation

The operator must immediately notify the person in charge of every fault or irregu-
larity.

If hazardous defects occur, the operator must immediately deactivate the device.
Hazardous defects include:

–

Malfunction of safety and monitoring devices

–

Damage to housing parts

–

Damage to electrical equipment

Collect any leakage of fluids and operating fluids immediately and dispose of it ac-
cording to the locally applicable guidelines.

Tools and other objects should only be kept in their designated places.

2.7

Maintenance tasks

Wear protective equipment:

–

Sealed safety goggles

–

Safety shoes

–

Safety gloves for protection against cuts

Locally applicable laws and regulations on work safety and accident prevention
must be complied with.

The procedure described in the installation and operating instructions for shutting
down the product/unit must be strictly observed.

Only perform the maintenance work described in these installation and operating
instructions.

Only original parts from the manufacturer may be used for maintenance and re-
pairs. The use of any non-original parts releases the manufacturer from any liabil-
ity.

Disconnect the device from the mains and secure it against being switched on
again without authorisation.

All rotating parts must be at a standstill.

Close the gate valve in the inlet and in the pressure pipe.

Collect any leakage of fluid and operating fluid immediately and dispose of it ac-
cording to the locally applicable guidelines.

Store tools at the designated locations.

After completing work, reattach all safety and monitoring devices and check that
they function properly.

Содержание Atmos GIGA-B





































































Результаты поиска

Содержание Atmos GIGA-B

Отзывы:

Похожие инструкции для Atmos GIGA-B

Бренды по названию

Популярные бренды

Wilo Atmos GIGA-B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Atmos GIGA-B

Отзывы:

Похожие инструкции для Atmos GIGA-B

Бренды по названию

Популярные бренды