Shenzhen Bayite Technology Co., Ltd
Email: [email protected]
Precautions
WARNING
※
This temperature controller is rated for 10 amps maximum. This
is 1100 watts at 110 volts or 2200 watts at 220 volts. Check the
power requirements of your intended output device prior to use
to ensure compatibility.
※
DO NOT OVERLOAD THE CONTROLLER; DOING SO MAY
RESULT IN FIRE!
— For safe operation —
WARNING
Installation
●
Connect this unit’s power cord only to an AC outlet of the type
stated in this User’s Guide or as marked on the unit. Failure to
do so is a fire and electrical shock hazard.
●
Do not allow water to enter this unit or allow the unit to
become wet. Fire or electrical shock may result.
● Do not place a container with liquid on or near the
controller. Liquid inside this unit is a fire and electrical
shock hazard.
●
Do not place heavy objects, on top of the power cord. A
damaged power cord is a fire and electrical shock hazard.
In particular, be careful not to place heavy objects on a power
cord covered by a carpet.
●
Be sure to connect to an appropriate outlet with a protective
grounding connection. Improper grounding can result in elec-
trical shock.
Operation
●
Do not scratch, bend, twist, pull, or heat the power cord. A dam-
aged power cord is a fire and electrical shock hazard.
●
Do not remove the unit’s cover. You could receive an electrical
shock. If you think internal inspection, maintenance, or repair is
necessary, contact your dealer.
●
Do not modify the unit. Doing so is a fire and electrical shock haz-
ard.
●
If lightning begins to occur, turn off the power switch of the unit as
soon as possible, and unplug the power cable plug from the electri-
cal outlet.
●
If a lightning strike has occurred, do not touch the power cable
plug if it is still connected. Doing so may be an electrical shock
hazard.
In case an abnormality occurs during operation
●
Using the unit with a damaged power cord is a fire and electrical
shock hazard.
●
Should this unit be dropped or damaged, turn the power switch
off, remove the power plug from the AC outlet. If you continue
using the unit without heeding this instruction, fire or electrical
shock may result.
●
If you notice any abnormality, such as smoke, odor, or noise, or if
a foreign object or liquid gets inside the unit, turn it off immedi-
ately. Remove the power cord from the AC outlet. Consult your
dealer for repair. Using the unit in this condition is a fire and elec-
trical shock hazard.
CAUTION
Installation
●
Keep this unit away from the following locations:
- Locations exposed to oil splashes or steam, such as near cook-
ing stoves, humidifiers, etc.
- Unstable surfaces, such as a wobbly table or slope.
- Locations exposed to excessive heat, such as inside a car with
all the windows closed, or places that receive direct sunlight.
- Locations subject to excessive humidity or dust accumulation.
●
Do not place the power cord close to a heater. It may melt, causing
fire or electrical shock.
●
Hold the power cord plug when disconnecting it from an AC out-
let. Never pull the cord. A damaged power cord is a potential fire
and electrical shock hazard.
●
Do not touch the power plug with wet hands. Doing so is a poten-
tial electrical shock hazard.
●
To relocate the unit, turn the power switch off, remove the
power plug from the AC outlet, and remove all connecting
cables. Dam- aged cables may cause fire or electrical shock.
●
When setting up the product, make sure that the AC outlet you
are using is easily accessible. If some trouble or malfunction
occurs, immediately turn off the power switch and
disconnect the plug from the outlet. Even when the power
switch is turned off, electricity is still flowing to the product at
the minimum level. When you are not using the product for a
long time, make sure to unplug the power cord from the wall AC
outlet.
●
Do not place the device in a location where it may come into con-
tact with corrosive gases or salt air. Doing so may result in mal-
function.
