Will Burt INFLEXION HD Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 84

background image

I

NSTRUCTIONS FOR

N

IGHT

S

CAN

L

ITE

&

I

NFLEXION

HD

TP-5554501-B

Original Instructions

2-9

May 2019

2.6 System Installation

This section describes installation of the Night Scan Lite and Inflexion HD.

The following is a quick summary of installation. Detailed steps follow the quick summary
(Section 2.6.1 and Section 2.6.2).

In general, install the Mast System as follows:

1. Select a Suitable Mounting Location (Section 2.6.1.1)

2. Unpack the Mast Assembly (Section 2.6.1.2)

3. Secure the Mast Assembly (Section 2.6.1.3)

4. Secure the Junction Box (Section 2.6.1.4)

5. Install Additional Accessories (Optional) (Section 2.6.1.5)

6. Partially Extend the Mast Manually (Section 2.6.2.1)

7. Wire Junction Box to Main Control Board (Section 2.6.2.2)

8. Wire Vehicle Interlock (Section 2.6.2.3)

9. Wire Optional Auxiliary Devices to Power Relay Board (Section 2.6.2.4)

10. Wire Power for Optional Auxiliary Devices to Power Relay Board (Section 2.6.2.5)

11. Wire Power for Lights to Power Relay Board (Section 2.6.2.6)

12. Wire Power for Mast and Control to Power Relay Board (Section 2.6.2.7)

13. Finalize Electrical Installation (Section 2.6.2.8)

Note the Inflexion HD substitutes an alternate payload for

“lights”, but the same procedure

applies.

2.6.1 Physical Installation Detailed Instructions

The following are detailed steps describing the physical installation of the Night Scan Lite and
Inflexion HD. The exact installation procedures may vary based on the configuration of the
system being used and the installation environment. Use the best and safest method for your
circumstances.

These instructions assume that the mounting hole locations are not pre-drilled and that the
Night Scan Lite or Inflexion HD components will be used as templates to drill these holes during
installation. Alternatively, the mounting hole location could be found and pre-drilled using the
installation dimensions (Section 2.4). When pre-drilling the mounting holes, use care to ensure
the mounting holes properly align.

«
...
39
40
41
42
43
...
»

Содержание INFLEXION HD





















































































Отзывы:

Нет отзывов

Похожие инструкции для INFLEXION HD

Бренд: Canta Страницы: 2

Бренд: Cadman Страницы: 66

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: Hama Страницы: 38

Бренд: NanoVibronix Страницы: 2

Бренд: NanoVibronix Страницы: 32

Shapes Hexagons

Бренд: Nanoleaf Страницы: 27

Бренд: Ultrawave Страницы: 30

Бренд: Ultrasound Technologies Страницы: 12

Бренд: UFO Страницы: 12

Бренд: M-Audio Страницы: 3

Бренд: Xtralis Страницы: 26

Implantmed SI-1010

Бренд: W&H Страницы: 2

Бренд: Econo-Wrap Страницы: 27

Бренд: U.S.SAWS Страницы: 21

ClusterStor H-6167

Бренд: Cray Страницы: 39

Elitco Lighting C202

Бренд: ELEGANT Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды