Wilkes WEB2, Руководство пользователя, Страница: 34 / 44

34
1. On the remote control, press VCR once; it will
blink once. Then press and hold SETUP until
the VCR key blinks twice.
2. Enter 9 9 2 . The VCR key will blink twice.
3. Press AUD once, then press VCR once. The
VCR key will blink twice.
The VCR key is now ready to be programmed for
your second audio device. See “Programming Device
Control.” To re-assign other device keys, repeat these
and substitute the key sequence using the following
chart:
NOTE:
Only one device can be assigned to an unused
device key at a time.
To Re-Assign Perform Key Sequence
VCR as 2
nd
AUD key
VCR
à
SETUP
à
9
à
9
à
2
à
AUD
à
VCR
VCR as 2
nd
TV key
VCR
à
SETUP
à
9
à
9
à
2
à
TV
à
VCR
CR as 2
nd
STB
key
VCR
à
SETUP
à
9
à
9
à
2
à
STB
à
VCR
VCR back to
VCR VCR
à
SETUP
à
9
à
9
à
2
à
VCR
à
VCR
To re-assign another unused device key, substitute
it for the VCR key above and then perform the se-
quence. For example, to re-assign an unused AUD
key as a second DVD key, perform:
AUD
à
SETUP
à
9
à
9
à
2
à
DVD
à
VCR
When a re-assignment is done, the selected device
key (e.g., AUD ) will blink twice to confirm your choice.
At that time, you will need to program device control
(see “Programming Device Control”).
CLEARING CUSTOM PROGRAMMING
The Wilkes Remote Control contains a Custom Pro-
gramming Reset program. You can use it to remove
all custom programming, except your setup codes
and reassigned device keys.
IMPORTANT:
Executing this program will erase all cus -
tom settings for Volume Lock, Learned Keys, Tune-In
Keys, and Channel Lock. However, your device pro -
gramming remains.
1. On the remote control, press and hold SETUP
until the last-selected device key blinks twice.
2. Enter 9 8 0. The last-selected device key
blinks twice, pauses, and blinks twice again
to confirm that all custom programming is
cleared.
TROUBLESHOOTING
PROBLEM: Device key does not blink when you press
a key.
SOLUTION: Replace the batteries with two (2) new AA
batteries (see “Installing Batteries”).
PROBLEM: Device key blinks when you press a key,
but home entertainment device does not respond.
SOLUTION: Make sure you are aiming the remote
control at your home entertainment device and that
you are within 15 feet of the device you are trying to
control.
PROBLEM: The remote control does not control home
entertainment devices or commands are not per-
forming properly.
SOLUTION: Try all listed codes for the device brand
being set up. Make sure all devices can be operated
with an infrared remote control.
PROBLEM: TV/VCR Combo does not respond proper-
ly.
SOLUTION: Use the VCR codes for your brand. Some
combo units may require both a TV code and a VCR
code for full operation.
PROBLEM: No volume on a second TV.
SOLUTION: Follow instructions under “Changing
Volume Lock.”
PROBLEM: PLAY and STOP keys do not work on a
Motorola DCT-2000 cable converter.
SOLUTION: Re-program the STB key for cable code
0476 (see “Programming Device Control”).
PROBLEM: Tried Search Method and still could not
find a working code.
SOLUTION: Try the Search Method again after clear -
ing out the device key as follows:
a. Press and hold SETUP until device key
blinks twice.
b. Enter 9 9 2.
c. Press and release the device key to be
cleared twice.