30
CHECKING THE CODES
You may need to find out which four-digit code is
operating your equipment.
For example, to find out which code is operating your TV:
1.
On the remote control, press
TV
once; it will
blink once. Then press and hold
SETUP
until
the
TV
key blinks twice.
2.
Enter
9 9 0.
The
TV
key will blink twice.
3.
To view the code for the first digit, press
1
once. Count the number of times the
TV
key
blinks (e.g., 3 blinks = 3) and write down the
number in the leftmost “TV Code” box.
NOTE:
If a code digit is 0, the selected mode key will
not blink.
4.
Repeat step 3 three more times for the
remaining digits. Use
2
for the second digit,
3
for the third digit, and
4
for the fourth digit.
Finish writing down the code in the TV Code
boxes in this guide.
5.
To check for other device codes, repeat steps
1 through 4, but substitute the appropriate
key (e.g.,
VCR, DVD, AUD,
or
STB
) for the de-
vice you are checking. Write down the codes
in the appropriate boxes.
USING LEARNING
The Wilkes Remote Control includes a Learning
feature (not available on all models) so you can add
functions that are unique to your home entertain-
ment devices (e.g. VCR Tracking Up or Down). Howev
-
er, there are some considerations.
Learning Precautions
► Your original remote controls must be in work
-
ing order for learning to work properly.
► Learned keys are mode-specific, so each one
can store a unique function for each mode.
► Do not use the following keys for learning:
Device Keys, SETUP, Record (•), Tune-In Keys.
► Learning capacity is approximately 16 to 25
keys, depending on the code being learned.
►
Certain device functions are not learnable
including multi-frequency types, some high
frequency ones, and other unusual formats.
►
For optimum learning, avoid high levels of
ambient light such as natural sunlight or
energy-efficient fluorescent lights.
NOTE:
Please have your original remote controls
handy before programming learning.
Programming a Learned Key
1.
Press and hold
SETUP
until the last-selected
mode key blinks twice, then press
9 7 5.
NOTE:
If the LED displays one long flash instead, ei
-
ther your batteries are low, or the Remote Control has
a memory fault.
2.
Press a mode key once (i.e.,
VCR, DVD, AUD,
TV,
or
STB
) to assign a mode for learning.
3.
Press the desired key on the Remote once to
store the feature to be learned.
4.
Place the Wilkes Remote Control head-to-
head (about 2” apart) from your original
remote control. Also locate the key (on your
original remote control) that you want the
Wilkes Remote Control to learn.
5.
On the original remote, press and hold the
key to be learned. The Wilkes Remote Con
-
trol’s LED will blink rapidly, then turn off. Con
-
tinue holding the key on the original remote
until the LED blinks twice.
NOTE:
If the LED displays one long blink, a learning
error has occurred. Try repeating this step again until
a successful capture occurs. If the function is still
not captured, press and hold
SETUP
to exit program-
ming and review the “Learning Precautions” on the
previous page. If needed, also see “Troubleshooting.”
After review, start programming again at step 1.
6.
Repeat steps 2 through 5 for another mode
and/or key or press and hold
SETUP
until
the active mode key LED blinks twice to exit
programming.
Содержание WEB2
Страница 1: ...1 USER GUIDE 336 973 3103 wilkes net...
Страница 42: ...42 NOTES...
Страница 43: ...43 NOTES...