Wilfa Lillehammer 12, Руководство по эксплуатации

Страница: 68 / 74

12
English
9 I FEEL button
Press this button to start I FEEL function and ” ” will be displayed on the remote controller. After this function is set, the
remote controller will send the detected ambient temperature to the controller and the unit will automatically adjust the indoor
temperature according to the detected temperature. Press this button again to close I FEEL function and ”
” will disappear.
• Please put the remote controller near user when this function is set. Do not put the remote controller near the object of high
temperature or low temperature in order to avoid detecting inaccurate ambient temperature. When I FEEL function is turned
on, the remote controller should be put within the area where indoor unit can receive the signal sent by the remote controller.
Signal between remote control and indoor unit will be sent each 10 minutes.
10 LIGHT button
Press this button to turn off display light on indoor unit. ” ” icon on remote controller disappears. Press this button again to
turn on display light. ” ” icon is displayed.
11 CLOCK button
Press this button to set clock time. ” ” icon on remote controller will blink. Press ” p ” or ” q ” button within 5s to set clock
time. Each pressing of ” p ” or ” q ” button, clock time will increase or decrease 1 minute. If hold ” p ” or “ q ” button, 2s later,
time will change quickly. Release this button when reaching your required time. Press “CLOCK” button to confirm the time.
”
” icon stops blinking.
Note:
• Clock time adopts 24-hour mode.
• The interval between two operation can’t exceeds 5s. Otherwise, remote controller will quit setting status. Operation for
TIMER ON/TIMER OFF is the same.
12 TIMER ON / TIMER OFF button
• TIMER ON button
”TIMER ON” button can set the time for timer on. After pressing this button, ” ” icon disappears and the word ”ON” on
remote controller blinks. Press ” p ” or “ q ” button to adjust TIMER ON setting. After each pressing ” p ” or ” q ” button,
TIMER ON setting will increase or decrease 1min. Hold ” p ” or ” q ” button, 2s later, the time will change quickly until
reaching your required time. “XX“resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is started
up, press ”TIMER ON” button to cancel it.
• TIMER OFF button
”TIMER OFF” button can set the time for timer off. After pressing this button,” ” icon disappears and the word ”OFF”
on remote controller blinks. Press ” p ” or ” q ” button to adjust TIMER OFF setting. After each pressing ” p ” or ” q ”
button, TIMER OFF setting will increase or decrease 1min. Hold ” p ” or ” q ” button, 2s later, the time will change quickly
until reaching your required time. Press ”TIMER OFF” word ”OFF” will stop blinking. ” ” icon resumes displaying. Cancel
TIMER OFF. Under the condition that TIMER OFF is started up, press ”TIMER OFF” button to cancel it.
Note:
• Under on and off status, you can set TIMER OFF or TIMER ON simultaneously.
• Before setting TIMER ON or TIMER OFF, please adjust the clock time.
• After starting up TIMER ON or TIMER OFF, set the constant circulating valid. After that, air conditioner will be turned on or
turned off according to setting time. ON/OFF button has no effect on setting. If you don’t need this function, please use
remote controller to cancel it.
FUNCTION INTRODUCTION FOR COMBINED BUTTONS
Energy saving function
• Under cooling mode, press ”TEMP” and ” CLOCK” buttons simultaneously to start up or turn off energy-saving function.
When energy-saving function is started up, ”SE” will be shown on remote controller, and air conditioner will adjust the set
temperature automatically according to ex-factory setting to reach to the best energy-saving effect. Press ”TEMP” and
”CLOCK” buttons simultaneously again to exit energy-saving function.
Note:
• Under energy-saving function, fan speed is defaulted at auto speed and it can’t be adjusted.
• Under energy-saving function, set temperature can’t be adjusted. Press ”TURBO” button and the remote controller won’t
send signal.
• Sleep function and energy-saving function can’t operate at the same time. If energy-saving function has been set under
cooling mode, press sleep button will cancel energy-saving function. If sleep function has been set under cooling mode,
start up the energy-saving function will cancel sleep function.