WHITESTAR SIGNATURE Скачать руководство пользователя страница 80

Страница: 80 / 100

5 • Anterior Segment Surgery Operating Modes

WHITESTAR SIGNATURE™ System

Rx Only – Z370147 Rev. C 1008

5-18

Using Vitrectomy

In the left panel, press

VIT 1

VIT 2

to select a submode.

VIT 1

is selected by

default.

Note: Each time you select the vitrectomy mode you are prompted to prime the

vitrectomy handpiece. Refer to Chapter 4,

Equipment Operation

, Priming

for Vitrectomy for detailed information.

Figure 5.17 – Vitrectomy Mode Screen

1. In the main panel, press the

Down

arrows to increase or decrease the

Aspiration Rate, Vacuum, or Cut Rate.

Note: If the Venturi pump is On, only the Vacuum and Cut Rate Settings are

shown.

2. To program the footpedal, go to

Configuration

Surgeons and Programs

Foot Pedal

Configuration, VIT

3. Select a

Submode

to program.

4. Edit the footpedal settings as needed.

Содержание SIGNATURE





































































































Результаты поиска

Содержание SIGNATURE

Отзывы:

Похожие инструкции для SIGNATURE

Бренды по названию

Популярные бренды

WHITESTAR SIGNATURE, Руководство владельца и эксплуатации

Результаты поиска

Содержание SIGNATURE

Отзывы:

Похожие инструкции для SIGNATURE

Бренды по названию

Популярные бренды