WHITESTAR SIGNATURE Скачать руководство пользователя страница 65

Страница: 65 / 100

5 • Anterior Segment Surgery Operating Modes

WHITESTAR SIGNATURE™ System

Rx Only – Z370147 Rev. C 1008

5-3

Figure 5.2 – Prime/Tune in Diathermy Mode

Using Diathermy

To begin Diathermy:

1. On the left panel press

DIA

2. Press the desired DIA submode button (

DIA 1

is selected by default).

The elapsed DIA time is displayed in the upper left corner as “DT”.

In the main panel, you can increase or decrease the power by pressing the
diathermy

Power

Down

arrows. If

Linear

power is selected, you can use the

footpedal to increase or decrease the power up to the maximum preset value.

To change the power delivery, press

Settings

. The

Settings

window opens. Set the

power delivery to

Panel

Linear

Burst

. Linear delivery is the default.

•

Panel

– Diathermy power is delivered consistently at the power level (%)

selected and indicated on the screen as Panel Maximum Power.

•

Linear

– Diathermy power is delivered from 5% to the maximum selected value

(Maximum Power) as the footpedal is pressed.

•

Burst

– Diathermy is delivered as a single 150 ms pulse, at the selected power,

as the footpedal is pressed.

Содержание SIGNATURE





































































































Результаты поиска

Содержание SIGNATURE

Отзывы:

Похожие инструкции для SIGNATURE

Бренды по названию

Популярные бренды

WHITESTAR SIGNATURE, Руководство владельца и эксплуатации

Результаты поиска

Содержание SIGNATURE

Отзывы:

Похожие инструкции для SIGNATURE

Бренды по названию

Популярные бренды