White Rodgers Electro-Air 10C27S-010 Скачать руководство пользователя страница 8

8

OPERATION

1.

With the 240 VAC power turned on at the circuit
breaker for the furnace, push the air cleaner ON-OFF
switch to the “ON” position (Figure 21).

2.

With the furnace blower running, the air cleaner will
be operating. An arcing or “snapping” sound may be
heard. This will occur occasionally, however the unit
is operating properly.

3.

With the furnace blower running, the Operating Light
should be ON. If the Operating Light is not ON this
signifies that the cells need washing, or that trouble
exists in the unit.

If, after washing the cells, the Operating Light stays off,
the cell could be wet, improperly placed in the cabinet or
may need servicing.

NOTE: An occasional flicker of the light accompanied by
harmless sparking or snapping noise may occur. This is
caused by trapping large particles of dirt. If arcing is
continuous, the cells should be washed or checked for
service problems see Basic SST/UST Service Guide.

Operating
Light

On-Off 
Switch

9.

Remove junction box cover and install the required
bushing into the 3/4 in. Knock out. With the supply
voltage turned off, route three (3) wires into junction
box for connections. (See Fig. 19.)

Insure all wires are clamped, wire connectors prop-
erly installed and grommets used to prevent wire
abrasion.

10. With the cabinet Installed, reinstall pre-filter(s) and

collecting cell(s) (Figure 20).

NOTE: The contact button and handles on the cell
must be facing you and ionizing wires must be on the
air intake side.

11. Install the power pack as follows:

Engage the lip on lower inside edge of power pack in
the flange on cabinet and carefully close the power
pack, making sure that the electrical connector prongs
on the power pack enter the slots in the socket on
cabinet. When the power pack is fully in place, en-
gage the latch and snap it closed.

Front View

Hot

Hot

Grounding
Conductor

Figure 19

Figure 20

Cabinet

Pre-Filters

Handle

Contact
Button

Contact
Button

Collecting Cells

Power Pack

Figure 21

Содержание Electro-Air 10C27S-010

















Отзывы: