background image

Failure to comply with the following warnings could 
result in personal injury or property damage.

FIRE HAZARD

•  Do not exceed the specified voltage.
•  Protect the control from direct contact with water 

(dripping, spraying, rain, etc.)

•  If the control has been in direct contact with water, 

replace the control.

•  Label all wired before disconnection when servicing 

controls. Wiring error can cause improper and 
dangerous operation.

•  Route and secure wiring away from flame.

SHOCK HAZARD

•  Disconnect electric power before servicing.
•  Ensure proper earth grounding of appliance.
•  Ensure proper connection of line neutral and line 

hot wires.

EXPLOSION HAZARD

•  Shut off main gas to appliance until installation is 

complete.

Installation should be done by a qualified heating and air 
conditioning contractor or licensed electrician.
Do not exceed the specification ratings.
All wiring must conform to local and national electrical codes 
and ordinances.
This control is a precision instrument, and should be handled 
carefully. Rough handling or distorting components could cause 
the control to malfunction.
Following installation or replacement, follow manufacturer's 
recommended installation/service instructions to ensure proper 
operation.

50M58-289

2-Stage, X-13 Style Hot Surface Ignition Control

INSTALLATION INSTRUCTIONS

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE 
INSTALLING  OR  OPERATING THIS  CONTROL  COULD  CAUSE  PERSONAL 
INJURY AND/OR PROPERTY DAMAGE.

 

 PRECAUTIONS

CONTENTS

Description ............................................................. 1

Precautions ............................................................ 1

Specifications ......................................................... 2

Installation .............................................................. 3

 

Mounting & Wiring

Operation ................................................................ 6

System Lockout and Diagnostic Features .............. 7

Troubleshooting ...................................................... 8

 

 DESCRIPTION

Do  not  short  out  terminals  on  gas  valve  or  primary 

control. Short or incorrect wiring may damage the 
thermostat.

CAUTION

!

WARNING

!

The 50M58-289 is a replacement control for two-stage automatic 
gas ignition controls employing a microprocessor to continually 
monitor, analyze, and control the proper operation of the gas 
burner and inducer. The 50M58-289 controls a multiple tapped 
induction circulation blower.
Signals interpreted during continual surveillance of the two-
stage thermostat and flame sensing element initiate automatic 

ignition of the burner, sensing of the flame, and system shutoff 
during normal operation.
The control incorporates system fault analysis for quick gas 
flow shutoff, coupled with automatic ignition retry upon sensing 
a fault correction.

www.white-rodgers.com

www.emersonclimate.com

PART NO. 37-7547B

Replaces 37-7547A

1445

Содержание 50M58-289









Отзывы: