White Outdoor LT 542H Скачать руководство пользователя | Manualshive

Страница: 42 / 48

background image

Page 14

Four-Cycle Engine • Vertical Crankshaft • Air-Cooled

181-887-14

III. Fuel System

To avoid stale gas and carburetor problems, treat the fuel
system in the following method below:

NOTES

Tecumseh recommends using

ULTRA-FRESH™

or Fuel

Saver Plus Gasoline Stabilizer plus Fuel System Cleaner as
an acceptable method of minimizing formation of fuel gum
deposits during storage. This product is available from your
Authorized Tecumseh Servicing Dealer.

Always follow mix ratio found on stabilizer container. Failure
to do so may result in equipment damage.

It is not necessary to drain stabilized gas from carburetor.

IV. Fuel Treatment

1. Add fuel stabilizer according to manufacturer’s

instructions.

2. Run engine at least 10 minutes after adding stabilizer

to allow it to reach carburetor.

NEVER store the engine with fuel in
the fuel tank inside a building with

potential sources of ignition such as hot water and space
heaters, clothes dryers, electric motors, etc.

NOTE

Instead of using a fuel preservative/stabilizer, you can
empty the fuel tank as described under "I. Draining Fuel”
instructions. See "B. Extended Storage” instructions.

B. Extended Storage

I. Draining Fuel

NOTES

Clean debris from engine before draining fuel from
carburetor. See "I. Clean Engine" instructions on page 13.

If you have prepared your fuel for short term storage it is not
necessary to drain fuel that contains stabilizer from your
carburetor. See "A. Short Term/Seasonal Storage"
instructions on page 13.

To avoid severe injury or death,
DO NOT pour fuel from engine or

siphon fuel by mouth.
1. To prevent serious injury from fuel fires, empty fuel tank

by running engine until it stops from lack of fuel. DO
NOT attempt to pour fuel from engine.

2. Run the engine while waiting until the remaining fuel is

consumed.

NEVER leave the engine
unattended when it is running and

NEVER run engine in enclosed areas.
3. Begin servicing the cylinder bore. See "II. Oil Cylinder

Bore" instructions on page 15.

!

WARNING

!

WARNING

!

WARNING

«
...
40
41
42
43
44
...
»

Содержание LT 542H

















































Отзывы:

Нет отзывов

Похожие инструкции для LT 542H

Бренд: Vari Страницы: 56

MULTICLIP Pro 51 S

Бренд: Stiga Страницы: 10

Бренд: MTD Страницы: 4

Бренд: Sears Страницы: 56

FREEDOM Z SFZ36-17KA

Бренд: Scag Power Equipment Страницы: 69

Z Master Professional 5000 Series

Бренд: Toro Страницы: 80

ELM 34/1400 PLUS

Бренд: F.F. Group Страницы: 48

Бренд: Gardena Страницы: 11

Бренд: Gardenline Страницы: 24

Бренд: Dixon Страницы: 48

Бренд: Poulan Pro Страницы: 60

Бренд: SaMASZ Страницы: 22

Бренд: Snapper Страницы: 224

Бренд: MTD Страницы: 36

Бренд: STEELE PRODUCTS Страницы: 23

Бренд: Webb Страницы: 24

PERFORMANCE 50562X89

Бренд: YARD KING Страницы: 60

Бренд: Toro Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды