background image

Page 20

Four-Cycle Engine • Vertical Crankshaft • Air-Cooled

181-887-14

Revised January, 2004

CALIFORNIA & US EPA EMISSION CONTROL WARRANTY STATEMENT

The U. S. Environmental Protection Agency (“EPA”), the
California Air Resources Board (“CARB”) and Tecumseh Power
Company are pleased to explain the Federal and California
Emission Control Systems Warranty on your new small off-road
engine. In California, new 1995 and later small off-road engines
must be designed, built and equipped to meet the State’s
stringent anti-smog standards. In other states, new 1997 and later
model year engines must be designed, built and equipped, at the
time of sale, to meet the U.S. EPA regulations for small non-road
engines. Tecumseh Power Company will warrant the emission
control system on your small off-road engine for the periods of
time listed below, provided there has been no abuse, neglect,
unapproved modification, or improper maintenance of your small
off-road engine.
Your emission control system may include parts such as the
carburetor, ignition system and exhaust system. Also included
may be the compression release system and other emission-
related assemblies.
Where a warrantable condition exists, Tecumseh Power
Company will repair your small off-road engine at no cost to you
for diagnosis, parts and labor.

MANUFACTURER’S EMISSION CONTROL 
SYSTEM WARRANTY COVERAGE

Emission control systems on 1995 and later model year California
small off-road engines are warranted for two years as hereinafter
noted. In other states, 1997 and later model year engines are also
warranted for two years. If, during such warranty period, any
emission-related part on your engine is defective in materials or
workmanship, the part will be repaired or replaced by Tecumseh
Power Company

OWNER’S WARRANTY RESPONSIBILITIES

As the small off-road engine owner, you are responsible for the
performance of the required maintenance listed in your Operator’s
Manual, but Tecumseh Power Company will not deny warranty
solely due to the lack of receipts or for your failure to provide
written evidence of the performance of all scheduled
maintenance.
As the small off-road engine owner, you should, however, be
aware that Tecumseh Power Company may deny you warranty
coverage if your small off-road engine or a part thereof has failed
due to abuse, neglect, improper maintenance or unapproved
modifications.

You are responsible for presenting your small off-road engine to a 
Tecumseh Authorized Service Outlet (any Tecumseh Registered 
Service Dealer, Tecumseh Authorized Service Distributor or 
Tecumseh Central Warehouse Distributor) as soon as a problem 
exists. The warranty repairs should be completed in a reasonable 
amount of time, not to exceed 30 days.
Warranty service can be arranged by contacting either an 
Authorized Tecumseh Servicing Dealer and/or Tecumseh Power 
Company, c/o Service Manager, 900 North Street, Grafton, WI 
53024-1499. Telephone 1-262-377-2700 [or in USA/Canada call 
1-800-558-5402].

IMPORTANT NOTE

This warranty statement explains your rights and obligations
under the Emission Control System Warranty (“ECS Warranty”)
which is provided to you by Tecumseh Power Company pursuant
to California law. Tecumseh Power Company also provides to
original purchasers of new Tecumseh Power Company engines.
The Tecumseh Power Company Limited Warranties for New
Tecumseh Engines and Electronic Ignition Modules (“Tecumseh
Power Company Warranty”) are located on the back cover of the
Operator’s Manual, enclosed with all new Tecumseh Power
Company engines. The ECS Warranty applies only to the
emission control system of your new engine. To the extent that
there is any conflict in terms between the ECS Warranty and the
Tecumseh Power Company Warranty, the ECS Warranty shall
apply except in any circumstances in which the Tecumseh Power
Company Warranty may provide a longer warranty period. Both
the ECS Warranty and the Tecumseh Power Company Warranty
describe important rights and obligations with respect to your new
engine.
Warranty service can only be performed by a Tecumseh Power
Company Authorized Servicing Dealer. At the time of requesting
warranty service, evidence must be presented of the date of sale
to the original purchaser. The purchaser shall pay any charges for
making service calls and/or for transporting the products to and
from the place where the inspection and/or warranty work is
performed. The purchaser shall be responsible for any damage or
loss incurred in connection with the transportation of any engine
or any part(s) thereof submitted for inspection and/or warranty
work.
If you have any questions regarding your warranty rights and 
responsibilities, you should contact Tecumseh Power Company at 
1-262-377-2700 or in USA/Canada call 1-800-558-5402.

Содержание LT 542H

















































Отзывы: