White Mountain Hearth 1 Скачать руководство пользователя

Страница: 3 / 60

23552-4-0408

Page 3

DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

• Due to high temperatures the appliance should be

located out of trafﬁc and away from furniture and

draperies.

• The glass front or any part removed for servicing

the appliance must be replaced prior to operating

the appliance. Work should be done by a qualiﬁed

service person.

•  Keep burner and control compartment clean.
•  Vent cap is hot while ﬁreplace is in operation.
•  Installation  and  repair  should  be  done  by  a

QUALIFIED SERVICE PERSON. The appliance

should be inspected before use and at least annually

by a qualified service person. More frequent

cleaning may be required due to excessive lint from

carpeting, bedding materials, etc. It is imperative

that control compartments, burners and circulating

air passageways of the appliance be kept clean.

• DO NOT put anything around the ﬁreplace that will

obstruct the ﬂow of ventilation air.

• Clearance in accordance with local installation codes

and the requirements of the gas supplier.

• DO keep the appliance area clear and free from

combustible material, gasoline and other ﬂammable

vapors and liquids.

• DO examine venting system periodically and replace

damaged parts.

• DO make a periodic visual check of pilot and burners.

Clean and replace damaged parts.

• CAUTION: The glass used in your ﬁreplace is

tempered glass. If the glass is cracked or damaged in

any way, it should be replaced only with a complete

glass frame assembly from Empire. See parts list on

Page

49 for ordering.

• DO NOT use this ﬁreplace if any part has been under

water. Immediately call a qualiﬁed service technician

to inspect the heater and to replace any part of the

control system and any gas control which has been

under water.

• Any safety screen or guard removed for servicing

an appliance must be replaced prior to operating

the appliance.

• If this appliance is installed directly on carpeting,

tile or other combustible material other than wood

ﬂooring the appliance shall be installed on a metal or

wood panel extending the full width and depth of the

appliance.

The base referred to above does not mean the ﬁreproof

base as used on wood stoves. The protection is for rugs

that are extremely thick and light colored tile.

• Children and adults should be alerted to the hazards

of high surface temperatures and should stay away

to avoid burns or clothing ignition.

• Young children should be carefully supervised when

they are in the same room as the appliance.

• Clothing or other ﬂammable material should not be

placed on or near the appliance.

• Adequate accessibility clearances for servicing and

proper operation.

• This appliance must not share or be connected to a

ﬂue serving a separate solid-fuel burning appliance.

• Keep the area around your appliance clear of

combustible materials, gasoline and other ﬂammable

vapor and liquids.

• Under no circumstances should any solid fuels (wood,

coal, paper or cardboard etc.) be used in this appli-

ance.

• The ﬂow of combustion and ventilation air must not

be obstructed in any way.

IMPORTANT SAFETY INFORMATION

Содержание 1





























































Результаты поиска

Содержание 1

Отзывы:

Похожие инструкции для 1

Бренды по названию

Популярные бренды

White Mountain Hearth 1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание 1

Отзывы:

Похожие инструкции для 1

Бренды по названию

Популярные бренды