White Mountain Hearth 1 Скачать руководство пользователя

Страница: 37 / 60

23552-4-0408

Page 37

Figure 56

Attention: Do not use Figure 56 or Figure 57 to order logs. Refer to

parts list on page 49 and parts view on page 50 to order logs and/or

ember material for your appropriate ﬁreplace model.

Before you begin: If you are installing logs into the DVD42 or

DVD48 model then this ﬁreplace is supplied with a set of seven

ceramic ﬁber logs. Do not handle these logs with your bare hands.

Always wear gloves to prevent skin irritation from ceramic ﬁbers.

After handling logs, wash your hands gently with soap and water

to remove any traces of ﬁber.
The positioning of logs is critical to safe and clean operation of

this ﬁreplace. Sooting and other problems may result if the logs

are not properly and ﬁrmly positioned in the ﬁreplace. Please refer

Figure 52

and

Figure 53

and corresponding WARNING when

completing following log placement steps.
1. Remove top louver, grasp louver, lift and pull forward.

2. Lower bottom louver, lift and hinge forward.

3. Release two glass frame spring clamps at bottom of ﬁrebox

4. Remove glass frame spring assembly.

5. Place front logs (#1, #2, and #3) between grates and main

burner. Align notches on front logs with locator tabs in base.

6. Place middle log (#4) between front and rear loop of burner.

Note: do not place on top of pilot assembly.

7. Place rear log (#5) on rear log shelf. Bottom ﬂange is to be

placed between the log shelf and burner tube.

8. Place bottom "Y" branch (#6) onto ﬂat areas of middle log (#4)

and bottom end of "Y" branch to the back side of the grate

tang (4th one from the left).

9. Place top branch (#7) onto ﬂat area of rear log (#5) and over

the front of "Y" branch.

10. Place decorative rock in front of grates and sides of main

burner.

11. After all logs are properly positioned, place small "dime" size

pieces of Rockwool lightly across the front burner tube ports.

Place the ember material (Rockwool pieces) side by side. Do

not stack more than one layer of embers across the burner

ports. See Figure 53.

12. Replace glass frame onto ﬁrebox.

13. Secure the two glass frame spring clamps at bottom of

ﬁrebox.

14. Align the tabs on top louver brackets with slots in front posts

to secure top louver.

15. Close bottom louver. Lift slightly to engage the end tabs into

the slots in ﬁreplace sides to close louver panel.

Figure 57

EMBER MATERIAL

PLACEMENT

LOG PLACEMENT (7 LOG SET)

ATTENTION

: Do not place decorative rock on logs or on

burner. The decorative rock should only be placed on the

ﬁreplace ﬂoor.

Warning: Failure to position the parts in accordance with

this diagram or failure to use only parts speciﬁcally approved

with this appliance may result in property damage or

personal injury.

Содержание 1





























































Результаты поиска

Содержание 1

Отзывы:

Похожие инструкции для 1

Бренды по названию

Популярные бренды

White Mountain Hearth 1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание 1

Отзывы:

Похожие инструкции для 1

Бренды по названию

Популярные бренды