White Mountain Hearth 1 Скачать руководство пользователя

Страница: 39 / 60

23552-4-0408

Page 39

STANDING PILOT OPERATING INSTRUCTIONS

REMOTE/OFF/ON Switch

The ﬁreplace is equipped with a REMOTE/OFF/ON switch. A

wire harness is attached to the REMOTE/OFF/ON switch. The red,

black and green (wires) female push-ons attach to the REMOTE/

OFF/ON switch. At the opposite end of the wire harness, the black

and green (wires) female push-ons attach to the gas valve. An ad-

ditional green wire and the red wire, which are stripped and bare,

will attach to one of the accessories that can be purchased for use

with your ﬁreplace.

Operation of REMOTE/OFF/ON Switch with no Accessories

To ignite main burner, turn the control knob on the gas valve from

the PILOT position to the ON position. Turn the REMOTE/OFF/ON

switch from the OFF position to the ON position. The additional green

wire and red wire, which are stripped and bare are not used.

Wall Switch, FWS-1

Connect the green and red, stripped and bare, wires on the

REMOTE/OFF/ON switch wire harness to the wall switch. Turn

the REMOTE/OFF/ON switch to the REMOTE position. Pivot the

rocker switch on the FWS-1 to the ON position.

Wall Thermostats (optional)

TRW - Wireless for Millivolt models

TMV - Reed switch for Millivolt models

Battery Operated Remote Controls, FRBC, FBRTC, and

TRW

Connect the green and red, stripped and bare, wires on the

REMOTE/OFF/ON switch wire harness to the remote receiver

that is a component in the remote kit. Turn the REMOTE/OFF/ON

switch to the REMOTE position. Follow instructions included with

the remote to complete installation.

Note:

If batteries fail in the remote, and immediate heat is desired,

turn the REMOTE/OFF/ON switch from the REMOTE position

to the ON position.

Electric (120 volt) Operated Remote Control, FREC

Connect the green and red, stripped and bare, wires on the REMOTE/

OFF/ON switch wire harness to the wires on remote receiver that

is a component in the FREC. Turn the REMOTE/OFF/ON switch

to the REMOTE position. Follow instructions in the FREC to

complete installation.

Note

: If electric (120 volt) fails in FREC, and immediate heat is

desired, turn the REMOTE/OFF/ON switch from the REMOTE

position to the ON position.

Installation of Remote Receiver

Place remote receiver on the ﬂoor of ﬁreplace behind the louver

as far forward as possible.

Attention:

The Velcro loop and hook are not necessary in this

installation but can be used to secure remote receiver.
Refer to remote control installation and operating instructions for

more details on remote control.

Millivolt Control

The valve regulator controls the burner pressure which should be

checked at the pressure test point. Turn captured screw counter

clockwise 2 or 3 turns and then place tubing to pressure gauge over

test point (Use test point “A” closest to control knob). After taking

pressure reading, be sure and turn captured screw clockwise ﬁrmly

to re-seal. Do not over torque. Check for gas leaks.
Millivolt thermopile is self generating. Gas valve does not require

24 volts or 110 volts.

Check System Operation

Millivolt system and all individual components may be checked

with a millivolt meter 0-1000 MV range.

It is important to use wire of a gauge proper for the length of the

wire:

Recommended Wire Gauges

Maximum Length

Wire Gauge

1' to 10'

10' to 25'

25' to 35'

OPERATING INSTRUCTIONS (continued)

Содержание 1





























































Результаты поиска

Содержание 1

Отзывы:

Похожие инструкции для 1

Бренды по названию

Популярные бренды

White Mountain Hearth 1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание 1

Отзывы:

Похожие инструкции для 1

Бренды по названию

Популярные бренды