7
Refrigerator Door
1. Remove the screw cover. See Graphic 6.
2. Remove refrigerator handle assembly as shown. Keep all
parts together. See Graphic 6.
3. Remove door hinge hole plug from refrigerator door. Move to
opposite side hinge hole as shown. See Graphic 3.
4. Remove door handle sealing screws. Move to opposite side of
refrigerator door as shown. See Graphic 4.
5. Remove door handle hole plug and discard. See Graphic 7.
Replace on opposite side with the door handle hole plug
provided in the Reversibility Kit located in the crisper.
6. Remove door stop. Move to opposite side of refrigerator door
as shown. See Graphic 5.
7. Position refrigerator handle on opposite side of the refrigerator
door as shown. See Graphic 6. First, drive top two screws in
handle first. Align lower portion of handle and drive bottom
screw into handle.
8. Tighten all screws. Set aside refrigerator door until bottom
hinge is installed on refrigerator.
9. Replace screw cover. See Graphic 6.
Style 2 - Contour Door Models
Graphics follow these instructions.
Cabinet
1. Remove the three dome caps and screws from handle side
and move them to opposite side. See Graphic 1-1.
2. Using the three
⁵⁄₁₆
"
hex-head hinge screws, insert two screws
halfway into the holes, leaving space to insert the center
hinge.
3. Slide the center hinge, from the right, onto the screws, insert
the third screw, and tighten all screws completely.
NOTE: Make sure the washers are in place on both the top
and bottom pins of the center hinge.
4. Remove cabinet hinge hole plugs from the cabinet top and
move them to opposite side hinge holes as shown. See
Graphic 1-2.
Freezer Door
1. Remove the freezer door handle. Using a
¹⁄₈
" hex key, loosen
the setscrew located on the side of the handle. Pull the handle
straight out from the door. Keep all parts together. See
Graphic 2.
2. Remove the brand badge using the plastic tool (provided).
Replace it with the badge provided in the Reversibility Kit
located inside the crisper. For proper placement, see the
Brand Badge Placement template (the last page of this
manual).
NOTES:
■
To avoid scratching the finish, do not use a sharp or
metallic object to pry the brand badge from the door.
■
Rub a small amount of liquid dish soap over any adhesive
residue with your fingers. Rinse the door with warm water
and dry with a soft cloth.
3. Remove door stop. Move to opposite side of freezer door as
shown. See Graphic 4.
4. Reinstall freezer handle on opposite side of the freezer door as
shown. See Graphic 2.
5. Tighten all screws. Set aside door until hinges and refrigerator
compartment door are in place.
Refrigerator Door
1. Remove the refrigerator door handle. Using a
¹⁄₈
" hex key,
loosen the setscrew located on the side of the handle. Pull the
handle straight out from the door. Keep all parts together. See
Graphic 6.
2. Remove door hinge hole plug from refrigerator door. Move to
opposite side hinge hole as shown. See Graphic 3.
3. Remove door handle hole plug and discard. See Graphic 7.
Replace on opposite side with the door handle hole plug
provided in the Reversibility Kit located in the crisper.
4. Remove door stop. Move to opposite side of refrigerator door
as shown. See Graphic 4.
5. Reinstall refrigerator handle on opposite side of the
refrigerator door as shown. See Graphic 6.
6. Tighten all screws. Set aside refrigerator door until bottom
hinge is installed on refrigerator.
Replace Doors and Hinges
NOTE: Graphic may be reversed if door swing is reversed.
1. Replace the parts for the bottom hinge as shown. Tighten
screws. Replace the refrigerator door.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
2. Measure the distance from the bottom of the refrigerator door
to the floor. The distance should be approximately 3
¹⁄₂
"
(88 mm).
NOTE: If necessary, loosen the bottom hinge, without
removing the screws, adjust the door to the correct height and
fully tighten the screws.
3. Assemble the parts for the center hinge as shown and tighten
all screws. See Center Hinge graphic. Replace the freezer
door.
A.
⁵⁄₁₆
" Hex-head hinge screws
B. Washers
Door Hinge
Hole Plug
Cabinet Hinge
Hole Plug
Dome Cap
Dome Cap
Washer
Setscrew
Shoulder
Screw
Shoulder
Screw Washer
Door Stop
Screw
Flat-Head
Handle
Screw
Door Handle
Hole Cap
A
A
B
Содержание WRT511SZDB
Страница 64: ......