Whirlpool WFW94HEX Series, Техническое образование

Страница: 11 / 86

2-2
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. See “Alterna�ve Parts”. Minimum siphon
break height: 28" (710 mm) from bo�om of washer. (Addi�onal
hoses may be needed.)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. A
1
/
4
" (6 mm)
diameter to 1" (25 mm) diameter Standpipe Adapter Kit is
available (Part Number 3363920). Top of standpipe must be at least
30" (762 mm) high; install no higher than 96" (2.44 m) from bo�om
of washer. If you have an overhead sewer and need to pump
higher than 96 inches, a sump pump and associated hardware are
needed. See “Alterna�ve Parts”.
Wall standpipe drain system
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Top of laundry tub must
96" (2.44 m) from bo�om of washer.
4
1
/
2
"
(113 mm)
Floor standpipe drain system
4
1
/
2
"
(113 mm)
30"
(762 mm)
min.
4 1 /
2
"
(113 mm)
Floor drain system
DRAIN SYSTEM
IMPORTANT:
To avoid siphoning, only 4.5" (113 mm) of drain
hose should be inside standpipe. Always secure drain hose with
beaded �e strap.
LOCATION REQUIREMENTS
LOC ATION REQUIREMENTS
Proper installaon is your responsibility.
You will need:
� A water heater set to 120° F (49° C).
�
A grounded electrical outlet located within 6 (1.8 m) of
power cord on back of washer.
�
Hot and cold water faucets located within 4 (1.2 m) of hot
20-100 psi (137.9-689.6 kPa).
�
washer. Installing on carpet or surfaces with foam backing is
not recommended.
� Floor must support washer’s total weight (with water and load)
of 315 lbs (143 kgs).
IMPORTANT: Do not install, store or operate washer where
it will be exposed to weather or in temperatures below 32° F
(0° C). Water remaining in washer aer use may cause damage
in low temperatures. See “Washer Care” in Washer Use and Care
Guide for winterizing informaon.
All dimensions show recommended spacing allowed, except for
closet door venlaon openings which are the minimum required.
For each arrangement, consider allowing more space for ease of
installaon and servicing, and spacing for companion appliances
Space must be large enough to allow door to fully open.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed, top
and boom air openings in door are required.
31
1
/
2
"
(800 mm)
27"
(686 mm)
38"
(965 mm)
51"
(1295 mm)
1"
(25 mm)
1"
(25 mm)
39" min.
(990 mm)
Custom under counter installaon:
7"
(178 mm)
14"
(356 mm)
1"
(25 mm)
4"
(102 mm)
1"
(25 mm )
Custom cabinet installaon:
Recessed area or closet installaon (washer only):
34" min.
(864 mm )
1"
(25 mm)
4"
(102 mm)
24 in.
2
(155 cm
2
)
48 in.
2
(310 cm
2
)
3"
(76 mm)
3"
(76 mm)
1"
(25 mm)
1"
(25 mm)
5"
(127 mm)
24 in .
2
(155 cm
2
)
48 in .
2
(310 cm
2
)
3"
(76 mm)
3"
(76 mm)
77
1
/
2
"
(1969 mm)
6"
(152 mm)
1"
(25 mm)
Recessed area or closet installaon
(stacked washer and dryer):