manualshive.com logo in svg

Whirlpool WFC7500VW0, Руководство пользователя

Поделиться
Скачать
Whirlpool WFC7500VW0 Скачать руководство пользователя страница 86

6-14

MOTOR OVERHEATS

1. Check drive motor.

2. Unplug washer or disconnect power.
3. Check wire harness connections.

4. Check drive belt.
5. Plug in washer or reconnect power.

6. Check for obstruction between the spin basket and the outer tub.

WON'T DRAIN

1. Unplug washer or disconnect power.

2. Check wire harness connections.
3. Check drain pump.

4. Check drain pump motor.
5. Check that the drain hose and drain pump filter are clear of foreign objects .

6. Plug in washer or reconnect power.
7. Verify CCU operation by running a Quick Diagnostic Test or any cycle.

MACHINE VIBRATES

1. Remove shipping system.
2. Check installation.

3. Check leveling feet.

INCORRECT WATER 

TEMPERATURE

1. Check that the inlet hoses are connected properly.
2. Unplug washer or disconnect power.

3. Check water temperature sensor for an abnormal condition. See the Water Temperature Sensor section, page 10.
4. Plug in washer or reconnect power.

5. Verify CCU operation by running a Diagnostic Test or any cycle.

DISPLAY FLASHING

See Failure/Error Display Codes.

Содержание WFC7500VW0



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды