Whirlpool WFC7500VW0 Скачать руководство пользователя страница 45

Страница: 45 / 90

4-9

3. Pry with a coin the lower front access

panel, then lower the panel, and remove

it.

Lower Front

Access Panel

5. Using a small screwdriver or a pair of

long-nosed pliers, pull the tension spring

on the retaining wire out from around

the front of the bellows, and remove the

wire.

4. Open the washer door.

Bellows

Retaining Wire

Tension Spring

6. Pull the bellows off the lip of the front

panel, and push the bellows inside the

front panel.

Door Switch

Assembly Screws

Retaining Wire

REMOVING THE FRONT PANEL ASSEMBLY

7. Remove the two screws from the door

switch assembly and two screws from

door lock assembly.

Door Lock

Assembly Screws

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before

operating.
Failure to do so can result in death or

electrical shock.

WARNING

Continued on the next page.

1. Unplug washer or disconnect power.
2. Turn off the water supply to the washer.

Door Switch

Assembly

Door Lock

Assembly

Содержание WFC7500VW0



























































































Результаты поиска

Содержание WFC7500VW0

Отзывы:

Бренды по названию

Популярные бренды

Whirlpool WFC7500VW0, Руководство пользователя

Результаты поиска

Содержание WFC7500VW0

Отзывы:

Бренды по названию

Популярные бренды