Whirlpool WFC7500VW0 Скачать руководство пользователя страница 74

Страница: 74 / 90

6-2

FAILURE CODES

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

DISPLAY

AFFICHAGE

EXPLANATION AND RECOMMENDED PROCEDURE

NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED

Water level is not reached within a defined time in normal wash cycle.

A09

Possible Causes/Procedure

If there is no water in the unit:

Make sure that both valves at the water sou rce(s) are turned on all the way.

Check for plugged or kinked inlet hoses or plugged screens in the inlet valves.

Verify inlet valve operation.

If there is water in the unit:

Verify drain pump operation.

Remove hose from pressure switch. Dislodge any debris build up in the hose inside the outer tub.

Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch.

1. Verify there is not a siphon problem.

2. Unplug washer or disconnect power.

3. Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU).

4. Check all hoses for possible leaks.

5. Plug in washer or reconnect power

6. Verify pressure switch operation.

7. Verify CCU operation by running a Quick Diagnostic Test or any cycle

LONG DRAIN

If the drain time exceeds 4 minutes the water valves turn off.

NOTES:

Rotate knob to clear the display.

A10

Possible Causes/Procedure

1. Check the drain hose and make sure it is not plugged or kinked .

2. Unplug washer or disconnect power.

3. Remove hose from pressure switch. Dislodge any debris build up in the hose inside the outer tub.

4. Check the electrical connections at the pump and make sure the pump is running.

5. Check the drain pump filter for foreign objects.

6. Plug in washer or reconnect power.

7. If the above does not correct the problem, go to step 8.

8. Unplug washer or disconnect power.

9. Replace the pump.

Содержание WFC7500VW0



























































































Результаты поиска

Содержание WFC7500VW0

Отзывы:

Бренды по названию

Популярные бренды

Whirlpool WFC7500VW0, Руководство пользователя

Результаты поиска

Содержание WFC7500VW0

Отзывы:

Бренды по названию

Популярные бренды