Whirlpool WFC7500VW0 Скачать руководство пользователя страница 71

Страница: 71 / 90

5-7

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

TEMPERATURE SENSOR

Refer to page 4-22 for the procedure for ac-

cessing the temperature sensor .
To check the temperature sensor at the

component terminals, perform the following

steps.
1. Unplug washer or disconnect power.
2. Disconnect the wire connector from the

temperature sensor or heater.

3. Set the ohmmeter to the R X 1K scale.
4. To check the temperature sensor, touch

the ohmmeter test leads to the sensor

terminals. The meter should indicate as

shown in the chart below.

To check the temperature sensor at the CCU,

perform the following steps.
1. Unplug washer or disconnect power.
2. Disconnect the temperature sensor con-

nector

SET2

(see page 4-5) from the

CCU.

3. Set the ohmmeter to the R X 1K scale.
4. Touch the ohmmeter test leads to con-

nector pins 1 and 2. The meter should

indicate as shown in the chart below.

Temperature

Results

F (0

35.9k

F (30

9.7k

104

F (40

6.6k

122

F (50

4.6k

140

F (60

3.2k

158

F (70

2.3k

203

F (95

Temperature

Results

F (0

35.9k

F (30

9.7k

104

F (40

6.6k

122

F (50

4.6k

140

F (60

3.2k

158

F (70

2.3k

203

F (95

Temperature

Sensor

SET2

Temperature Sensor

DU3

Door Switch

PR2

Pressure switch Input low voltage

5 6

1 2 1 2

1 2

5.
6.
7.

Содержание WFC7500VW0



























































































Результаты поиска

Содержание WFC7500VW0

Отзывы:

Бренды по названию

Популярные бренды

Whirlpool WFC7500VW0, Руководство пользователя

Результаты поиска

Содержание WFC7500VW0

Отзывы:

Бренды по названию

Популярные бренды