background image

4

Electrical Requirements

NOTE: All outdoor wiring must be suitable for outdoor use. Use 
copper conductors only.

All field wiring must be done in accordance with National 
Electrical Code requirements, applicable requirements of UL, 
or local codes, where applicable.

Electrical wiring, disconnect means and over-current 
protection are to be supplied by the installer. Refer to the 
rating plate for the maximum over-current protection, 
minimum circuit ampacity, and operating voltage. See the 
wiring diagrams in “Make Electrical Connections.”

INSTALLATION INSTRUCTIONS

Inspect Shipment

This heat pump is shipped in one package, completely 
assembled and wired. The thermostat is shipped in a separate 
carton when ordered.

1. Check the heat pump rating plate to confirm specifications 

are as ordered.

2. Upon receipt of heat pump, inspect it for possible shipping 

damage. Examine the heat pump inside the carton if the 
carton is damaged.

If damage is found, it should be noted on the carrier’s freight bill. 
Damage claims should be filed with the carrier immediately. 
Claims of shortages should be filed with the seller within 5 days.

NOTE: If any damages are discovered and reported to the carrier, 
do not install the heat pump because your claim may be denied.

WARNING

Rating Plate Ampacity

Less than 15

16 - 20

21 - 30

AWG

14

12

10

8

31 - 50

Electrical Shock Hazard

Electrically ground condensing unit or heat pump.

Connect ground wire to ground lug.

Use copper wire for supply connection.

Correct wire gauge is shown in the chart below.

Failure to follow these instructions can result in 
death or electrical shock.

Excessive Weight Hazard

Use two or more people to move and install 
condensing unit or heat pump.

WARNING

Failure to do so can result in back or other injury.

Содержание W4GH8





















Отзывы: