Whirlpool Light programmable oven Скачать руководство пользователя

Страница: 30 / 35

- 30 -

Error codes

Error code 3:

GENRA HOT

Generator too hot (Generator thermoswitch has tripped. Reconnect

by pressing button under oven.)

Error code 4:

OVEN HOT

Oven too hot (Oven chamber thermoswitch has tripped. Reconnect

by pressing button under oven.)

Error code 5:

FAN HOT

Fan too hot (Thermoswitch in motor has tripped. Wait for 10

minutes and try again.

Error code 6:

DRAIN > 75

Drain too hot (Drain temperature has been above 75

C for more

than 5 min. Check that jet in drain is working.)

Error code 7:

OVEN SENS

Oven sensor defective (Temperature sensor in oven chamber not

working properly.)

Error code 8:

PROBE SENS

Core temp. probe not connected (A program using core temp.

probe has been selected but probe has not been connected.)

Error code 9:

GENER SENS

Generator sensor defective (Temperature sensor in generator not
working.)

Error code 10: DRAIN SENS

Drain sensor defective (Sensor in drain not working. Oven can still

be used.)

Error code 11: WATER SHOR

Water shortage (Steam generator was not filled within two minutes.

Check that the water has been turned on.)

Error code 12: SSR HOT

SSR too hot (Solid-state relay too hot.)

Error code 13: GENER > 130

Generator too hot (Temperature in steam generator higher than

130°C. If fault recurs, descale generator)

Error code 14: FAN SPEED

Fan running too slow

Error code 15: CPU HOT

CPU board too hot (> 60°C)

Error code 16: IO BRD HOT

IO board too hot (> 60°C)

Error code 18: DATA ERROR

Error in set-up data

Error code 19: WRONG LANG Wrong language

Error code 20: NO COM IO

Internal defect (Failure in communication between computer and IO

board.)

Error code 22: NO RESTART

Restart not possible (Oven has been without power too long.)

Error code 23: OVEN WARM

Oven too hot at CombiWash start-up

Error code 24: DRAIN ERR

Draining failure (Drain blocked or failure of drain pump. Water level

in generator still high after 10 seconds of draining.)

Error code 25: PROBE ERR

Core temperature probe defective (1, 2 or 3 of the elements in

the core temperature probe defective.)

Error code 28: ALARM ERR

Configuration error in main alarms (3, 4, 5, 12) (warning)

Error code 29: DOOR SENS

Wrong door sensor signal (warning)

Error code 34: WATER PRES

Water pressure too low (Check that water is turned on.)

Error code 40: IO BRD HOT

Temperature in IO board critical (Warning after program run.)

Error code 43: WRONG SW

Wrong software version (Visual Cooking I oven)

Error code 44: DAMPER ERR

Failure during initialisation of exhaust at oven start-up

Error code 45: 24 V ERROR

24 V missing or failure of main contactor output

Содержание Light programmable oven




































Результаты поиска

Содержание Light programmable oven

Отзывы:

Похожие инструкции для Light programmable oven

Бренды по названию

Популярные бренды

Whirlpool Light programmable oven, Руководство по обслуживанию и установке

Результаты поиска

Содержание Light programmable oven

Отзывы:

Похожие инструкции для Light programmable oven

Бренды по названию

Популярные бренды