Whirlpool AER5522VAS0, Руководство пользователя

Страница: 53 / 70

3 3-
MRC II Double Oven, Electric (continued)
Models:
Models:
MRC II Control, Double Oven, Fan Convection (Lower)
Warming Zone, Electric
MRC II Control, Double Oven, True Convection (Lower)
Warming Zone, Electric
MET8775XB00
MET8775XS00
MET8775XW00
Released
MET8885XB00
MET8885XS00
MET8885XW00
YMET8885XB00
YMET8885XS00
YMET8885XW00
Released
Previous Offset shown, or U-00 is displayed.
Adjusts temperature in 5 ⁰F (3⁰C) increments
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Bake and Broil Temperatures are offset
automatically to the same degree.
If START is not pressed within 1 minute, adjustment
is ignored
Display
"TEST ON" ##⁰F "UO" (In the test mode)
"CONTROL RESET" (Resets Control settings)
"USAGE" (Displays hours of Operation)
"ENG MODE" (Manufacturing Information)
"TEST MODE" (Manual Check of Control relays)
"VERSION" (Manufacturing Information)
"DISPLAY" (Checks all LEDs in Display)
"FAULTS" *(Displays all Fault Codes)
"AUTO TEST" (Performs a complete check of the
OVEN, automatically)
*Press "DELAY START" to clear all fault codes.
"+" again
"+" again
Diagnostic Mode
Press CANCEL/CANCEL/START.
Press the TEMP/TIME "+" keypad,
follow directions at each operation.
Action
Press "+"
"+" again
"+" again
"+" again
The "AUTO TEST" program will automatically test all the oven circuits. This test is very easy to
use and when the test is complete, test results will be provided. Whenever servicing the oven,
this is the test to run.
When checking for Fault Codes and "NO FAULTS" is displayed. Do Not replace the Control.
When in the Diagnostic mode, instructions will be provided by the control to help you through
each of the programs. Press Cancel to exit the test at any time.
Temperature Adjustment
Press TEMP/TIME "+" or "-".
Press "SETTINGS" until "Temp Calib"
is displayed.
Press START.
"+" again
Previous Offset shown, or U-00 is displayed.
Adjusts temperature in 5 ⁰F (3⁰C) increments
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Bake and Broil Temperatures are offset
automatically to the same degree.
If START is not pressed within 1 minute, adjustment
is ignored
Display
"TEST ON" ##⁰F "UO" (In the test mode)
"CONTROL RESET" (Resets Control settings)
"USAGE" (Displays hours of Operation)
"ENG MODE" (Manufacturing Information)
"TEST MODE" (Manual Check of Control relays)
"VERSION" (Manufacturing Information)
"DISPLAY" (Checks all LEDs in Display)
"FAULTS" *(Displays all Fault Codes)
"AUTO TEST" (Performs a complete check of the
OVEN, automatically)
*Press "DELAY START" to clear all fault codes.
"+" again
"+" again
Diagnostic Mode
Press CANCEL/CANCEL/START.
Press the TEMP/TIME "+" keypad,
follow directions at each operation.
Action
Press "+"
"+" again
"+" again
"+" again
The "AUTO TEST" program will automatically test all the oven circuits. This test is very easy to
use and when the test is complete, test results will be provided. Whenever servicing the oven,
this is the test to run.
When checking for Fault Codes and "NO FAULTS" is displayed. Do Not replace the Control.
When in the Diagnostic mode, instructions will be provided by the control to help you through
each of the programs. Press Cancel to exit the test at any time.
Temperature Adjustment
Press TEMP/TIME "+" or "-".
Press "SETTINGS" until "Temp Calib"
is displayed.
Press START.
"+" again
*Press “START TIME or“DELAY START” to clear all fault codes.