Page 9
1. Put the unit into “indicator adjustment” Mode:
• Place the SLIDE SWITCH in the OFF position and turn all Momentary
switches off.
• Press and hold the WAIL switch.
• Press and release momentary switch 6.
• Release the WAIL switch.
To confirm that the unit is in title 13
operation, LEDs 2, 3 and 4 on the Arrow
indicator will light up for
two seconds
.
2. To make them brighter:
• Press and release the MANUAL switch until the desired intensity has
been met.
OR…
To make them dimmer:
• Press and release the AIRHORN switch until the desired intensity has
been met.
3. Store and activate the indicator intensity.
• Press and release the WAIL switch.
All of the indicator lights will turn off and the indicator intensity will be
stored. This will put the unit back into lighting operating mode.
(
11) - Changing Backlight intensity:
This procedure will allow adjustments to be made of the intensity of the
backlight LEDs on the control head.
Factory Default:
50%.
To adjust the backlight:
(
DIP SWITCH SETTING:
SWITCH 1, 2 & 3 ON / SWITCH 4 OFF)
1. Put the unit into “backlight adjustment” Mode:
• Place the SLIDE SWITCH in the OFF position and turn all Momentary
switches off.
• Connect J5 PIN 5 to +VBAT (To turn on the backlight).
• Press and hold the WAIL switch.
• Press and release momentary switch 7.
• Release the WAIL switch.
To confirm entry into “backlight adjustment”
mode,
LEDs 1 and 2 on the Arrow indicator
will light up.
2. To make them brighter:
• Press and release the MANUAL switch until the desired intensity has
been met.
OR…
To make them dimmer:
• Press and release the AIRHORN switch until the desired intensity has
been met.
3. Store and activate the backlight intensity.
• Press and release the WAIL switch.
All of the indicator lights will turn off and the backlight intensity will be
stored. This will put the unit back into lighting operating mode.
(12) Changing
SHUTDOWN DELAY:
This procedure will allow adjustments to
the time that the unit will operate after the
UNIT ENABLE input becomes inactive.
Factory Default:
OFF immediately
To adjust the Shutdown Delay:
(
DIP SWITCH SETTING:
SWITCH 1, 2 & 3
ON / SWITCH 4 OFF)
1. Put the unit into “Shutdown Delay adjustment” Mode:
• Place the SLIDE SWITCH in the OFF position and turn all Momentary
switches off.
• Press and hold the WAIL switch.
• Press and release momentary switch 8.
• Release the WAIL switch.
To confirm entry into “Shutdown Delay
adjustment” mode, the Arrow indicator will
display this pattern: (arrow leds 2,4)
2. To adjust the time of operation
•
Press and release the AIRHORN switch to cycle through time choices
until the desired time has been met (table 3)
3. Store and activate the time of
operation.
• Press and release the WAIL switch.
All of the indicator lights will turn off and the shutdown delay will be stored.
This will put the unit back into lighting operating mode.
Programming Siren tones:
DIP SWITCH SETTING:
Put the unit into
“tone programming mode”
by
placing DIP switch 1 into the
OFF
position and DIP switch 2-4 in the
ON
position (see wiring for DIP switch location). With the DIP switches in this
position lighting functions are disabled, leaving the siren functions and
tone programming active.
To change the primary tone for the WAIL, YELP and TONE 3
switch positions:
• Activate the switch position that you wish to change.
• Press and release the lighting momentary switch 4 to change the tone
produced by speaker 1.
OR…
• Press and release the lighting momentary switch 5 to change the tone
produced by speaker 2.
• Each time a switch is pressed and released, the next available tone will
be broadcast on the corresponding speaker.
AND…
• The other speaker will shut off for 2 seconds so that the new tone can
be clearly identified.
• When the desired tone is generated, it is automatically saved in that
switch position for that speaker.
To change the override tone for the WAIL, YELP and TONE 3
switch positions:
• Activate the switch position that you wish to change.
• Press and release the MANUAL switch to produce it’s override tone.
• Press and release the lighting momentary switch 4 to change the tone
produced by speaker 1.
OR…
• Press and release the lighting momentary switch 5 to change the tone
produced by speaker 2.
• Each time a switch is pressed and released, the next available tone will
be broadcast on the corresponding speaker.
AND…
OFF Immediately
1 minute
10 minutes
30 minutes
1 hour
2 hours
4 hours
8 hours
Table 3
Slide Switch Indicators
= OFF
= ON
1
2
3
Tone off
Wail
Phased wail
Wail 2
Yelp
Phased Yelp
Yelp 2
Yelp 249
Piercer
Hilo
Mechanical
Phased Mechanical
Mechanical 2
Warble
Phased Warble
Woop
Phased Woop
Wail Yelp combo
Wail Yelp Combo 2
Tone list for Wail, Yelp & Tone 3 buttons and their override tones, and all hf positions:
··
··
·
··
··
·
··
··
·
··
··
