Page 8
3. Add or delete momentary switches activated by the
selected switch:
• Press and release one of the 8 momentary switches to add or delete it
from the selected switch’s configuration. The switch’s indicator light will
turn on steady when its corresponding switch is selected to be
activated.
4. Store and activate the selected switch's configuration:
For a selected momentary switch:
• Place the SLIDE SWITCH in the OFF position.
• Press and release the RADIO switch.
All of the indicator lights will turn off and the data will be stored. This
will put the unit back into lighting operating mode, and this change
can be tested. To configure another switch start back at step 1.
(7) Copying a units configuration:
If there is more than one unit that needs to be configured to operate in the
same manor, it is not necessary to configure each unit separately. Once
one unit has been configured to operate as desired,
it can now be used as the “primary” unit and its configuration can be
copied to another unit that is set up as a “secondary” unit.
To copy a configuration to a second unit:
(
DIP SWITCH SETTING:
SWITCH 1, 2 & 3 ON / SWITCH 4 OFF)
1. Wire the units as follows:
• Connect J7 on both units to a common power source (PIN1 to (+)V BAT
& PIN 4 to Ground).
• Connect pin 10 of J5 on the “primary” unit to pin 5 of J5 on the
“secondary” unit.
• Connect pin 1 of J5 of both units to (+)V BAT, Leave all other wiring
unconnected.
2. Put the “PRIMARY” unit into “transmit” mode:
• Place the SLIDE SWITCH in the OFF position and turn all Momentary
switches off.
• Press and hold the RADIO switch.
• Press and release momentary switch 10.
• Release the RADIO switch.
To confirm entry into
“transmit”
mode, LEDs
4 and 5 on the Arrow indicator will light up.
3. Put the “SECONDARY” unit into “receive” mode:
• Place the SLIDE SWITCH in the OFF position and turn all Momentary
switches off.
• Press and hold the RADIO switch.
• Press and release momentary switch 9.
• Release the RADIO switch.
To confirm entry into “receive” mode,
LEDs
3 and 5 on the Arrow indicator will light up.
4. Transfer the Configuration:
• Watch the 3 slide switch indicators on the “SECONDARY” unit, when
the left most indicator turns on, proper communications have been
established.
• Press and release momentary switch 4 on the “primary” unit to start the
transfer.
• On the “PRIMARY” unit see that the left most indicator on the arrow
turns on to indicate that the transfer has been started.
• Watch the 3 slide switch indicators on the “SECONDARY” unit, in 5
seconds the middle indicator turns on and transfer is complete.
NOTE: If the right slide switch indicator light on the “secondary” unit
turns on, an error has occurred, press the RADIO on both units to
start back at step 1.
5. Store and activate the configuration:
• Press and release the RADIO switch on both the “primary and
secondary” units.
All of the indicator lights will turn off and the data will be stored. This
will put both units back into lighting operating mode.
OR...
• Turn the power off on both the “primary and secondary” units.
To transfer the configuration to another unit start back at step 1.
(8) Changing between standard and Title 13
operation:
When in title 13 operation, the airhorn tone will override the primary siren
tone on only one of the siren speakers, in standard operation, the airhorn
tone will override the primary siren tone on both of the siren speakers.
Factory Default:
standard operation.
(
DIP SWITCH SETTING:
SWITCH 1, 2 & 3 ON / SWITCH 4 OFF)
To change
between standard and Title 13 operation
:
• Place the SLIDE SWITCH in the OFF position and turn all Momentary
switches off.
• Press and hold the WAIL switch.
• Press and release momentary switch 4.
• Release the WAIL switch.
To confirm that the unit is in title 13
operation, LEDs 1, 3 and 5 on the Arrow
indicator will light up for
two seconds
.
To confirm that the unit is in standard
operation, LEDs 1 and 5 on the Arrow
indicator will light up for
two seconds
.
All of the indicator lights will turn off and the operation change will be
stored. This will put the unit back into lighting operating mode.
NOTE: The siren operations cannot be tested until the unit is out of
programming mode (i.e. all dip switches ON)
(9) Programming a tone set of Title 13 tones:
This procedure will program the unit with a default set of tones that will
meet title 13 requirements, and will change the unit to operate under title
13 guidelines as described in section (7).
(
DIP SWITCH SETTING:
SWITCH 1, 2 & 3 ON / SWITCH 4 OFF)
Programming a tone set of Title 13 tones
:
• Place the SLIDE SWITCH in the OFF position and turn all Momentary
switches off.
• Press and hold the WAIL switch.
• Press and release momentary switch 5.
• Release the WAIL switch.
To confirm that the title 13 defaults have
been set, LEDs 1 and 4 on the Arrow
indicator will light up for
two seconds
.
All of the indicator lights will turn off and the title 13 defaults will be stored.
This will put the unit back into lighting operating mode.
NOTE: The siren cannot be tested until the unit is out of
programming mode (i.e. all dip switches ON)
(10)Changing Red indicator intensity:
This procedure will allow adjustments to be made of the intensity of the
red indicator LEDs on the control head.
Factory Default:
50%.
To adjust the red LED indicator:
(
DIP SWITCH SETTING:
SWITCH 1, 2 & 3 ON / SWITCH 4 OFF)
