background image

Manual                          AMP 4200                                                       

 

Valid for                        

111-425-04-001-00

 

 

Version (modifications reseverd) 

21.02.2022 

Seite 1 of 17 

 

1. Welcome 

Thank you for buying this quality WHD product. Please read this manual carefully, especially the safety 
and security information. 
Please check that you have the correct manual for your product. To do this, please compare the product 
code number shown above with the product code number displayed on your product. 
 

AMP 4200 

Matrix Amplifier with 4 speaker zones (4-8 ohms/70V/100V) 
 

 

 
 

2. Inventory Checklist

 

- AMP 4200 
- 19 "bracket 
- Device feet (premounted) 
- Power cable 
- Operation manual 
 
 

3. Safety & Security 
General Information

 

In addition to this guidance please adhere to your own country-specific safety & security regulations. 
 

3.1. How to use this guide: 

Read these instructions carefully before use and use this product only in accordance with the instructions 
listed here. 
 

3.2. Signs & symbols used 

This sign warns of danger of injury and property damage. 

This sign warns of injury from electricity. 

 

This sign warns of injury and/or explosion. 

This symbol refers to additional information. 

 

3.3. Signal words and their meaning

 

Danger:

 Potential severe physical damage and acute danger. 

Warning:

 Potential electrical shock physical damage and severe property damage. 

Caution:

 Potential fire hazard physical damage or property damage as a result of. 

Attention:

 Advisory notes only. 

Содержание AMP 4200


















Отзывы: