Wharfedale Pro R1604 Скачать руководство пользователя страница 10

Connections

,,

The R series use 3 different types of connectors: 3 pin XLR, 1/4 jacks, and phone plugs. Some of these are 

balanced, some unbalanced, some are stereo and some have dual functions. These connectors are used in 

various ways as dhow in the following.

Microphone Inputs, Main Mix & ALT 3-4 Outputs

These are balanced on female XLR connectors and connected as shown. Cables connected to any 

microphone sockets should be wired with pin 1 ground, pin 2 hot(+ve) and pin 3 to cold(-ve). Use high quality 

shield pair cable or multicore with individually shield pairs.

Line Inputs

,,

These are balanced on 1/4 stereo type (TRS) jacks. Cable connected to any of these should use a stereo 

jack wired with TIP hot(+ve), RING cold(-ve) and SLEEVE to ground.

Insert Points

,,

All of the insert points have both SEND and RETURN signals on a single 1/4 stereo jack. Cables connected 

to any insert point should use a stereo jack wired with TIP return, RING send and SLEEVE to ground. Use 

individually shield cable for both send and return or twin cable with individual screening on each core.

Auxiliary send, EFX return and Control Room Outputs

,,

There are unbalanced on 1/4 jack. Cables connected to these inputs should use a mono jack wired with TIP 

signal and SLEEVE to ground.

Stereo 2 Track Inputs and Outputs

There are unbalanced on mono plugs. Cables connected to these should be wired PIN signal, and SLEVE to 

ground.

Headphone Output

,,

This is unbalanced on a 1/4 stereo jack. Cables connected to this output should be wired with TIP left signal, 

RING right signal, and SLEEVE to ground

3 pole jack  2 pole jack

Balanced   Unbalanced

Unbalanced Mic XLR

2. Hot (+ve)

Link 3 to 1

1. Screen

2. Hot (+ve)

3. Cold (-ve)

1. Screen

Balanced Mic XLR

Headphones

+ve lead to Tip

-ve lead to Ring 

Sleeve

Hot (+ve)

Cold (-ve)

Ground / 
  Screen

Ground / 
Screen

Signal

+ve lead to Tip

-ve lead and 
Sleeve to Ground

Left Signal

Right Signal

Ground

Inserts

Signal send

Signal return

Ground /
Screen

Sleeve

Ring

Tip

R1604 & R2004

R Series Mixers

.9.

Содержание R1604

















Отзывы: