background image

WD-8

 Rev. 4.0 (202202)

Operating instructions

39

4.2.4

Washing 

Make sure that the items are in a position where they cannot move out of the
washing basket during the washing and rinsing phases.

Remove large pieces of food by rinsing the dishes with a hand shower. The
water  in the hand shower must  not  exceed 40°C. Place the items to  be
washed in the basket.

Open the hood.

Put the lever (19) in the correct position for the items currently in the basket:
- is for normally soiled and + for heavily soiled dishware.

Select the programme. Slide the basket into the machine. If the machine is
fitted  with  “autostart”,  the  hood  closes  automatically  and  washing  starts
after the basket has been slid in.

Close  the  hood.  The  machine  starts  washing  using  the  selected
programme. The display (4) now shows the remaining washing time for the
programme.

The symbol (1) is lit during the washing phase.

Once the rinsing phase starts, the symbol (3) lights up. If the final rinse
water has not reached the correct rinse temperature once rinsing starts, the
symbol  (3)  flashes  and  the  machine  continues  washing  until  the  rinsing
water has reached the correct temperature.

Do not open the hood until the programme has finished.

If the hood is opened during the washing cycle, the machine will stop. If the
hood is closed again, the programme will start from the beginning.

When the machine has stopped, the selected programme appears on the
display  (4)  and  the  hood  opens  automatically  if  the  machine  has  an
automatic hood. Remove the washed items and allow them to dry.

P0  is  a  pause  mode  and  is  used  in  the  case  of  prolonged  intervals  between
washes in order to maintain the tank temperature. The hood must be closed. The
machine does not start in P0 mode.

Press  the  programme  button  for  the  current  programme  once.  "P0"
appears on the display (4). 

Press the button again to return to the current programme.

The hood must be opened and closed between each washing cycle.

Washing (PPE )(option)

When the machine is in PPE mode, all wash programmes restart three (3) times
in  a  row  which  enables  longer  wash  programmes  and  for  each  wash  cycle
sequence to have three rinses.

Содержание WD-8

























































Отзывы: