Wexiodisk WD-6 Скачать руководство пользователя страница 28

Страница: 28 / 60

Glass

tilt

Rev. 2.0 (202202)

Installation instructions

3.6

Installation and connection of auxiliary equipment and options

•

Once the machine is in place and has been adjusted horizontally and
vertically, the auxiliary equipment can be fitted.

•

The machine can be equipped with a number of options. Check what your
machine is equipped with, which depends on the model, machine type and
country.

The various options normally place no specific requirement on the installation.

3.6.1

Sinks and conveyors

The machine can be positioned so that it can be straight-loaded or corner-loaded.
Depending on the position chosen, the removable side support (4) on the basket
conveyor must be positioned as shown in the figures below.

Position of the side support

Dishwasher

Sink

Basket conveyor

Side support

Detail of sink cover

The connection profile must look like the one shown in the drawing. The distance
of 6 mm may be reduced, but must not be less than 3 mm.

G_sidostöd

G_300730

6mm

Содержание WD-6





























































Результаты поиска

Содержание WD-6

Отзывы:

Похожие инструкции для WD-6

Бренды по названию

Популярные бренды

Wexiodisk WD-6, Инструкция по установке и эксплуатации

Результаты поиска

Содержание WD-6

Отзывы:

Похожие инструкции для WD-6

Бренды по названию

Популярные бренды