Westinghouse TR18346 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 26

Westinghouse TR18346 Скачать руководство пользователя страница 19

WARNING

!

WARNING

!

(2) N eedle b earing

(3) C lutch d rum

(4) S pacer

(5) C lutch s hoe

4. Fuel f ilter

5. Oil f ilter

6. Front and Rear d ampers

Disassemble the filter and wash with gasoline, or

replace with new on if needed.

Disassemble the filter and wash with gasoline, or

replace with new on if needed.

Replace if adhered part is peeled or crack is

observed on the rubber part.

It is very important for smooth and safe

operation to keep the cutters always sharp.

Your cutters need to be sharpened

when:

Sawdust becomes powder-like.

You need extra force to saw in.

The cut way does not go straight

Vibration increases

Fuel consumption increases

Be sure to wear safety gloves.

Make sure the saw chain in held

sccurely

Make sure the engine is stopped

Use a round file of proper size for

your chain.

Chain type: 21VB

File size: 3/16 in (4.76 mm)

Before filing:

SAW CHAIN

10.MAINTENANCE OF SAW CHAIN

AND GUIDE BAR.

Cutter s etting s tandards:

(1) S procket

«
...
17
18
19
20
21
...
»

Содержание TR18346



























Отзывы:

Нет отзывов