Westinghouse TR18346 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 26

Westinghouse TR18346 Скачать руководство пользователя страница 18

oiling pot for clogging.(F26)

When the guide bar is dismounted, remove

Saw dust in the bar groove and the oiling port.(F27)

Grease the nose sprocket from the feeding

port on the tip of the bar.(F28)

Check for fuel leakage and loose fastenings and
damage to major parts.
especially handle joints and guide bar mounting. If
any defects are found, make sure to have them
repaired before operating again.

Dust clogging between the cylinder fins will cause
overheating of the engine Periodically check and
clean the cylinder fins after removing the air
cleaner and the cylinder cover.

When installing the cylinder cover, make sure that
switch wires and grommets are positioned
correctly in place.(F29)

Be sure to black the air intake hole.

Clean the electrodes with a wire brush and reset the
gap to 0.65 mm as necessary.

Check for cracks and for excesslve wear interfering
with the chain drive. If the wearing is found
obviously, replace it with new one. Never fit a new
chain on a worn sprocket, or a worn chain on a
new sprocket.

(1) O iling p ort

(2) G rease p ort

(3) S procket

3. Guide b ar

4. Others

1. Cylinder f ins

2. Spark p lug(F30)

3. Sprocket(F31)

PERIODICAL SERVICE POINTS

NOTE

F26

F27

F28

F29

F30

F31

«
...
16
17
18
19
20
...
»

Содержание TR18346



























Отзывы:

Нет отзывов