Westinghouse TR18346 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 26

Westinghouse TR18346 Скачать руководство пользователя страница 12

in the figure.(F12)
(1)Chain oil
The chain oil flow can be changed by inserting
a screwdriver in the hole on bottom of the clutch
side. Adjust according to your work conditions.
(F13)

The oil tank should become nearly empty by the
time fuel is used up. Be sure to refill the oil tank
every time when refueling the unit.

The carburetor on your unit has been factory
adjusted, but may require fine tuning due to change
in operating conditions. Before adjusting the
carburetor, make sure that provided are clean

air/fuel filters and fresh, properly mixed fuel. When
adjusting, take the following steps:

Be sure to adjust the carburetor with the
bar chain attached
1.Stop engine and screw in both H and L
needles until they stop. Never force. Then set them
back the initial number of turns as shown below.

Start engine and allow it to warm up at
half-throttle.
Turn L needle slowly clockwise to find a position
where idling speed is maximum, then set the
needle back a quarter(1/4) turn

counterclockwise.
Turn idle adjusting screw(T) counterclockwise
to that saw chain does not turn. If idling speed is
too slow, turn the screw clockwise.

ADJUSTING CARBURETOR(F14)

(1) Adjuster

3

H needle:

1 /

8

1

L needle:

1 /

4

2.

3.

4.

NOTE

NOTE

F13

F14

«
...
10
11
12
13
14
...
»

Содержание TR18346



























Отзывы:

Нет отзывов