Westinghouse TR18346 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 26

Westinghouse TR18346 Скачать руководство пользователя страница 11

Fill fuel and chain oil tanks respectively,

and tighten the caps securely.(F7)

Put the switch to “l” position.(F8)

While holding the throttle lever together with the

throttle interlock, push in the side throttle lock button

and release the throttle lever to hold it at the starting

position.(F9)

(1) Chain oil

(2) Fuel

(3) Switch

(4) Throttle lever

(5) Throttle interlock

(6) Choke knob

Pull out the choke knob to the closed position.(F10)

When restarting immediately after stopping the

engine, leave the choke knob at the open position.

While holding the saw unit securely on the

ground, pull the starter rope vigorously.(F11)

Do not start the engine while hanging the chain

saw with a hand. The saw chain may touch your

body. It’s very dangerous.

When engine has ignited first, push in the choke

knob and pull the starter again to start the engine

Allow the engine to warm up with the throttle lever

pulled slightly.

Keep clear of the saw chain as it will start

rotating upon starting of engine.

After starting the engine. run the chain at medium

speed and see if chain oil is scattered off as shown

7. OPERATING ENGINE

STARTING ENGINE

CHECKING OIL SUPPLY

1.

2.

3.

4.

5.

6.

7.

F7

F8

F9

F10

F11

F12

NOTE

(3)

(4)

(5)

(6)

WARNING

!

WARNING

!

«
...
9
10
11
12
13
...
»

Содержание TR18346



























Отзывы:

Нет отзывов