Westinghouse AC System Скачать руководство пользователя | Manualshive

Страница: 31 / 54

background image

Westinghouse Solar AC Installation Guide

Copyright © 2011 - Westinghouse Solar

27

|

P a g e

tightening down the 3/8" Flange nut against the L Bracket Once the array has been leveled, double
check all flange nuts and lags are properly secured.

Figure 18 -

Single row of Westinghouse Solar modules installed

Considerations for Wiring Westinghouse Solar AC Arrays with multiple rows

If your array is continuing to an upper row, prepare the last wiring harness connector in the first
row with an Extension Cable that will reach the upper row modules bulkhead connection.
Westinghouse Solar AC Extension Cables are available in a length of 6', 12' and 20'.

Tip: Careful planning of wiring layouts will create a quick installation without interruptions or the
need to purchase additional equipment.

Installing a Second Row of Modules

To install a second row of modules in the north-south direction, Westinghouse Solar North-South
Brackets are used as a structural component to connect module frames in adjacent rows. North-
South Brackets balance the load of both rows on a shared attachment point in the center of the
array.

«
...
29
30
31
32
33
...
»

Содержание AC System























































Отзывы:

Нет отзывов

Похожие инструкции для AC System

Бренд: Avalue Technology Страницы: 100

Бренд: Nibe Страницы: 28

PACK ELITE+ Series

Бренд: XUNZEL Страницы: 24

TouchBerry PI 10.1

Бренд: Industrial Shields Страницы: 20

Бренд: Waka Waka Страницы: 2

Бренд: Light Blue Optics Страницы: 28

VITOSOL 100-F SV1B

Бренд: Viessmann Страницы: 4

Q.MAXX-G5 Series

Бренд: Qcells Страницы: 12

Бренд: Jackery Страницы: 24

Бренд: IRIS Net Страницы: 76

Бренд: Aaeon Страницы: 29

Бренд: Aaeon Страницы: 61

Бренд: YASKAWA Страницы: 77

HMI-043T-EM41N-O

Бренд: Icop Страницы: 25

Бренд: ELGO Electronic Страницы: 24

Бренд: IBT Technologies Страницы: 28

Бренд: Westinghouse Страницы: 4

Бренд: IEI Technology Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды