background image

 

 

Dokument:  1597en06.doc 

 

Förf.:  LT/JJo 

 

 

Datum:  2017-11-30 

 

Sida:  7 av 9 

 
 
 

WESTERSTRAND URFABRIK AB 

 

 

 

Box 133 

Tel.  0506 48 000 

 

Internet:  

www.westerstrand.se 

545 23  TÖREBODA 

Fax. 0506 48 051 

 

E-mail: 

 [email protected]

 

  

7. Power failure 

In case of power failure, the consequences are as follows: 

 

-The master clock does not distribute any impulses. The impulses are stored in the memory of 
  the master clock.  

IMPORTANT!!

  Impulses are collected for max. 10 hours.  

 
-When power returns the master clock wi11 distribute the stored impulses to the movement by  
  rapid impulses (15 imp./min.).  
 
-Then the movement begins to forward the hands to correct time. 
  
-It will take some minutes (the time depends on how long the power failure has lasted) until  
  the movement has reset the hands).  
 
-After the movement has reached correct time it returns to normal operation. 

  

 

8. Maintenance 

 
Lubrication of the movement must be done minimum once a year.All positions marked in the 
pictures on the following pages must be lubricated. 
Movement placed in aggressive environment should be lubricated at more frequent intervals, particulary the 
bearrings on the shafts and the gear mechanism. 
Use high-grade lithium-soap paste, for specification please contact Westerstrand Urfabrik AB. 
 
In case of negligence of maitenance  the movement may be damaged or the life cycle considerable reduced. 

 

 

 

 

Содержание 115000-00











Отзывы: