background image

 

 

Dokument:  1597en06.doc 

 

Förf.:  LT/JJo 

 

 

Datum:  2017-11-30 

 

Sida:  2 av 9 

 
 
 

WESTERSTRAND URFABRIK AB 

 

 

 

Box 133 

Tel.  0506 48 000 

 

Internet:  

www.westerstrand.se 

545 23  TÖREBODA 

Fax. 0506 48 051 

 

E-mail: 

 [email protected]

 

1. General description of movement LMV 

 
The movement LMV is based on a 230V synchronous motor which moves the hands every minute via an 
echange gear mechanism. 
The movement is driven by 24V reversing impulses from a master clock, which are collected by a special  
Device, so-called impuls collector. 
The impulse collector includes an impulse controller which based on a cam and a micro switcher controls the 
current to the synchronus motor. When the contact points of the switcher are closed the motor starts. The LMV 
movement has a minute graded disc which indicates the position of the minute hand. This arrangement enable 
setting of correct time. 
The hour hand has not this feature and thus the position of the hour hand has to manually calculated and 
adjusted.  
 
The version LMV-UV complies to the feature and performance of LMV version with the exception that this 
movement only has one shaft for minute drive. This version is used for installations with separate gear for the 
hand. 
 
 
 
 
 
 
 

 

Содержание 115000-00











Отзывы: