Western Star 47X 2020 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 166

background image

ture, the oil will run more freely and ensure that
the axle is flushed.

4.

Clean the fill and drain plugs. Change them if
necessary.

4.1

For magnetic plugs, use a piece of key
stock or any other convenient steel slug
to short the two magnetic poles and divert
the magnetic field.

4.2

Clean away the collected material depos-
ited on each pole. Magnets will rapidly
lose their effectiveness as collected mate-
rial bridges the gap between the two
poles.

4.3

After the first oil is changed, inspect the
drain plug each time for large quantities
of metal particles.

5.

Fill the axle with the recommended lubricant.
See

for recommended drive axle lubri-

cants and

for lubricant capacities.

5.1

Fill the axle through the oil fill hole. Lubri-
cant should be level with the bottom of
the oil fill hole.

5.2

Install and tighten the fill plug 30 lbf·ft (41
N·m).

Detroit Drive Axle Lubricant, New Final Drive

*

Lubricant

Type

Ambient

Temperature

Must meet Detroit

Fluids Specification

(DFS) 93K219.03

Synthetic

–40°F (–40°C) and

up

†

*

Detroit rear axles do not require the use of friction modifiers.

†

There is no upper limit on the ambient temperature, but axle sump tem-

perature must never exceed 250°F (121°C).

Table 3, Detroit Drive Axle Lubricants, New Final

Drive

New Final Drive Oil Capacity, New Final Drive

Axle Type

Oil in Hubs (2)

Oil in Axle

NFD Model 4 Forward Axle SP

1.8 L

14 L

NFD Model 4 Rear Rear Axle SP

1.8 L

11 L

f350692

04/28/2020

Fig. 3, Detroit

™

New Final Drive Forward Axle, Oil Fill

Location

f350693

04/28/2020

Fig. 4, Detroit

™

New Final Drive Rear Axle, Oil Fill

Location

Rear Axle

35

47X and 49X Maintenance Manual, August 2020

35/3

«
...
97
98
99
100
101
...
»

Содержание 47X 2020







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 47X 2020

Бренд: Taylor-Dunn Страницы: 52

Бренд: RAM Commercial Страницы: 16

Бренд: Utilimaster Страницы: 11

Бренд: Eoslift Страницы: 8

Бренд: Eoslift Страницы: 8

EXPERT 2000 2002

Бренд: Labrie Страницы: 69

COLUMBUS McKINNON 040016431

Бренд: Pfaff Страницы: 24

Бренд: Gregory Страницы: 49

Бренд: Fuso Страницы: 520

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды