Westermo TD-32 Скачать руководство пользователя

Страница: 53 / 56

6178-2203

RS-232/V.24 Signals
TD

Transmitted Data. Data going from DTE to DCE.

Received Data. The Data going from DCE to DTE.

RTS

Request to Send. Hardware handshake generated by the DTE to determine if the DCE is ready to
receive data. Expected response is from the CTS line.

CTS

Clear To Send. Hardware handshake by DCE in response to an RTS signal.

DSR

Data Set Ready. The DCE-equipment is powered and usable.

DTR

Data Terminal Ready. The DTE-equipment is powered and usable.

DCD

Data Carrier Detect. A signal from the DCE indicating that a carrier is present on the line.

Simplex

Uni-directional communication.

Start bit

Marks the start of a character at asynchronous communication.

Stop bit

One or more stop bits marks the end of a character at asynchronous communication. Systems that
require more than one stop bit may have problems during communication via modems, since modems
most often remove the second stop bit.

Содержание TD-32

























































Результаты поиска

Содержание TD-32

Отзывы:

Похожие инструкции для TD-32

Бренды по названию

Популярные бренды

Westermo TD-32, Руководство по установке

Результаты поиска

Содержание TD-32

Отзывы:

Похожие инструкции для TD-32

Бренды по названию

Популярные бренды