11. Press a 1 3/4” Square Inner Cap (44) into the
Seat Frame (36). Attach a Bumper (73) to the
Seat Frame with a 1/2” Tap Screw (65).
Slide the Seat Frame (36) onto the 5/16” x
2 1/2” Carriage Bolts (1) in the Base (4). See
the inset drawing. The bracket on the Seat
Frame must be behind the Press Frame
(17). Hand-tighten a 5/16” Nylon Locknut (3)
onto each Carriage Bolt. Do not tighten the
Nylon Locknuts until the end of this
assembly step.
Attach the Seat Frame (36) to the Front
Upright (42) with two 5/16” x 2 3/4” Bolts (11),
two 5/16” Flat Washers (8), and two 5/16”
Nylon Locknuts (3).
Tighten all Nylon Locknuts used in this
step now.
12. Attach a Bumper (73) to the Rocker Arm (32)
with a 1/2” Tap Screw (65).
Lubricate a 3/8” x 3 1/4” Bolt (35). Attach the
Rocker arm (32) to the Base (4) with the 3/8”
x 3 1/4” Bolt and a 3/8” Nylon Locknut (21).
13. Lubricate a 3/8” x 2 1/2” Bolt (7). Attach the
Leg Lever (29) to the Rocker Arm (32) with
the 3/8” x 2 1/2” Bolt and a 3/8” Nylon Jam
Nut (33).
Press a 1 3/4” Square Inner Cap (44) into
each end of the Leg Lever (29).
13
11
8
12
9
ARM ASSEMBL
Y
12
Bracket
17
36
1
44
36
3
3
42
73
32
73
65
4
21
7—Lubricate
29
32
44
44
Lubricate—35
65
4
11
33
22. Locate the Short Cable (58). Route the
Short Cable under the 3 1/2” Low Pulley (77).
Be sure that the end of the Cable with the
ball is on the indicated side of the Pulley
and that the Cable is between the Pulley
and the welded spacer on the Leg Lever
(29). Tighten the 3/8” x 3 1/2” Bolt (16) and
the 3/8” Nylon Locknut (not shown).
23. Wrap the Short Cable (58) around a “V”-
Pulley (6). Attach the Pulley and a Long
Cable Trap (50) inside the bracket on the
Seat Frame (36) with a 3/8” x 2 1/2” Bolt (7)
and a 3/8” Nylon Locknut (21). Be sure that
the Cable Trap is turned to hold the Cable
in place and that the Cable is routed
around the Pulley as shown.
24. Wrap the Short Cable (58) around a 3 1/2”
Pulley (15). Attach the Pulley to the Rocker
Arm (32) with a 3/8” x 3 1/2” Bolt (16), a 3/8”
Flat Washer (9), and a 3/8” Nylon Locknut
(21). Be sure that the Cable Trap (66) is
turned to hold the Cable in place and that
the Cable is routed around the Pulley as
shown.
25. Note: The 3 1/2” Pulley (15) labelled in this
step is pre-attached. It is shown removed
for easy part identification.
Route the Short Cable (58) around the 3 1/2”
Pulley (15) attached to the lower hole in the
Front Upright (42). Be sure that the Cable
Trap (66) is turned to hold the Cable in
place and that the Cable is routed around
the Pulley as shown. Tighten the 3/8” Nylon
Locknut (21) and the 3/8” x 3 3/4” Bolt (71).
25
22
23
24
CABLE ASSEMBL
Y
58
77
Ball
16
58
6
21
16
66
15
32
9
21
29
7
50
36
58
42
21
71
58
9
66
15
Welded Spacer
