11
10
12
3
6
9
18
. Slide the Long Cable (66) between the 3 1/2”
Pulley (15) and the Cable Trap (59) on the
Narrow Swivel Bracket (58) on the left Arm (46),
in the direction shown. Note: The Pulley, the
Cable Trap, the 3/8” x 1 3/4” Bolt (12), and the
3/8” Jam Nut (6) are shown removed for clari-
ty. The Cable Trap must be turned to the 3
o’clock position.
19. Remove the 4 1/2” Pulley (77) from the Adjustment
“U” Bracket (75). Attach the Adjustment “U”
Bracket to the Front Upright (42) with a 5/16” x 3”
Short Thread Bolt (91), a 5/16” Flat Washer (8),
and a 5/16” Nylon Locknut (3). Note: This
Bracket is used to adjust the tension of the
Long Cable (66). Thread the Nylon Locknut
onto the Bolt only two complete turns.
Wrap the Long Cable (66) around the 4 1/2”
Pulley (77). Reattach the Pulley to the Adjustment
“U” Bracket (75) with the 3/8” x 1 3/4” Bolt (12)
and the 3/8” Jam Nut (6) that were removed.
20. See the inset drawing. Slide the Long Cable
(66) between the 3 1/2” Pulley (15) and the Cable
Trap (59) on the Narrow Swivel Bracket (58) on
the right Arm (46), in the direction shown. Note:
The Pulley, the Cable Trap, the 3/8” x 1 3/4”
Bolt (12), and the 3/8” Jam Nut (6) are shown
removed for clarity. The Cable Trap must be
turned to the 3 o’clock position.
Attach a 5/16” x 3” Bolt (17), two 5/16” Flat
Washers (8), and a 5/16” Jam Nut (2) to the indi-
cated hole in the Top Frame (67).
Slide the end of the Long Cable (66) onto the end
of the 5/16” x 3” Bolt (17). Tighten another 5/16”
Jam Nut (2) onto the Bolt. Do not overtighten
the Jam Nut.
21. Attach the 5/16” x 3 1/2” Bolt (87), two 5/16” Flat
Washers (8), the 1” Metal Spacer (22), and a
5/16” Nylon Locknut (3) to the lower hole in the
Front Upright (42) as shown.
Wrap the indicated end of the Short Cable (23)
under a 3 1/2” Pulley (15). Attach the Pulley to
the Front Upright (42) with a 3/8” x 3 1/2” Bolt
(16), a 3/8” Flat Washer (9), and a 3/8” Nylon
Locknut (21). The Short Cable must be between
the Pulley and the Metal Spacer (22).
20
21
66
2
2
8
46
66
6
59
12
87
16
8
22
23
8
3
9
21
15
42
46
58
15
8
17
67
12
3
6
9
18
19
12
46
58
15
59
77
91
6
75
12
66
3
8
42
66
6
12
3
6
9
10
14. Insert two 3/8” x 1 3/4” Bolts (12) through the two
“I” Plates (78) and two 4 1/2” Pulleys (77) as
shown. Finger tighten two 3/8” Nylon Locknuts
(21) onto the Bolts. Do not thread the Nylon
Locknuts fully onto the Bolts yet.
15. IMPORTANT: As you assemble the Long Cable
(66) and the Short Cable (not shown), refer to
the CABLE DIAGRAM on page 17 of this man-
ual to make sure that the Cables are properly
routed.
Find the end of the Long Cable (66) that has a
metal eyelet without a rubber ball. Insert that end
of the Long Cable up through the indicated open-
ing in the Top Frame (67).
Lay the Long Cable (66) over a 4 1/2” Pulley (77).
Attach the Pulley inside the Top Frame (67) with a
3/8” x 2 3/4” Bolt (70), two 3/8” Flat Washers (9),
two 1/2” x 1/2” Spacers (65), and a 3/8” Nylon
Locknut (21).
16. Remove the 3 1/2” Pulley (15) from inside the
bracket on the Top Frame (67). Insert the end of
the Long Cable (66) through the bracket and
down through the indicated hole in the Top
Frame.
Hold the 3 1/2” Pulley (15) inside the bracket on
the Top Frame (67). The Long Cable (66) must be
between the Pulley and the top of the bracket.
Attach the Pulley to the bracket with a 3/8” x
1 3/4” Bolt (12) and 3/8” Jam Nut (6) that were
removed.
17. Insert the Long Cable (66) between the “I” Plates
(78).
See the inset drawing. Slide the Long Cable (66)
between the 3 1/2” Pulley (15) and the Cable Trap
(59) attached to the Wide Swivel Bracket (71), in
the direction shown. Note: The Pulley, Cable
Trap, 3/8” x 1 3/4” Bolt (12), and 3/8” Jam Nut
(6) are shown apart for clarity.
16
17
12
67
Bracket
6
66
12
71
71
66
78
15
59
6
66
15
14
15
77
78
78
21
9
67
66
9
70
77
65
65
12
21
77
