9
12
22. Remove the preattached 3 1/2” Pulley (15) and
Cable Trap (59) from the Pulley Plate (20). Wrap
the Short Cable (23) under the Pulley. Reattach
the Pulley and the Cable Trap to the Pulley Plate
with the 3/8” x 1 3/4” Bolt (12) and the 3/8” Jam
Nut (6). The Cable Trap must be turned to the “6
o’clock” position.
Slide the Short Cable (23) over the lower 3 1/2”
Pulley (15) attached to the “I” Plates (78). Tighten
the two 3/8” Nylon Locknuts (21) attaching the
“I” Plates.
See the inset drawing. Slide the Slotted Flange
Bushing (89) over the Weight Tube (80), making
sure it is oriented as shown. Insert the end of the
Short Cable (23) into the upper end of the Weight
Tube. Slide the Weight Guide Bracket (81) onto
the top of the Weight Tube. Insert a 5/16” x 1 1/2”
Bolt (24) through the Weight Guide Bracket, the
Weight Tube and the end of the Short Cable.
Tighten a 5/16” Nylon Locknut (3) onto the Bolt.
IMPORTANT: The Short and Long Cables (23,
66) must be properly routed on the pulleys,
and the Cables must be properly tightened. To
tighten the Cables, refer to TROUBLE-SHOOT-
ING AND MAINTENANCE on page 16 of this
manual.
23. Attach the Backrest (41) to the Front Upright (42)
with two 1/4” x 2 1/2” Screws (43) and two 1/4”
Flat Washers (10).
24. Press a 1 1/2” Inner Cap (32) into the Seat Frame
(36).
Insert a 1/4” x 2” Carriage Bolt (38) into the centre
of each Seat Plate (37). Attach the Seat Plates to
the Seat (13) with four 1/4” x 3/4” Screws (18).
Insert the two 1/4” x 2” Carriage Bolts (38) into
the Seat Frame (36). Make sure that the Seat
(13) is turned so the wide end is toward the 1 1/2”
Inner Cap (32). Tighten two 1/4” Nylon Locknuts
(7) with two 1/4” Flat Washers (10) onto the
Carriage Bolts.
23
43
42
13
Wide
End
32
7
18
10
37
36
38
37
41
10
24
12
3
6
9
22
23
66
81
3
25
80
12
15
23
78
21
59
6
20
24
89
10. Insert the two 4 1/2” “L” Pins (60) down into the
indicated holes in the Arm Frame (52) and the
Arms (46).
12
13
56
62
62
21
21
56
9
9
46
46
71
76
67
3
60
52
46
47
48
48
47
45
33
8
49
8
45
46
46
3
51
10
11
13. Attach the Wide Swivel Bracket (71) to the brack-
et on the side of the Top Frame (67) with the
5/16” x 3 1/4” Bolt (76) and a 5/16” Nylon Locknut
(3). Do not overtighten the Nylon Locknut; the
Wide Swivel Bracket must be able to swivel
freely.
12. Attach a Large “U” Bracket (56) to one of the Arms
(46) with a 3/8” x 2 1/2” Bolt (62), a 3/8” Flat
Washer (9) and a 3/8” Nylon Locknut (21).
Attach a Large “U” Bracket (56) to the other Arm
(46) in the same manner.
11. Wet the lower ends of the Arms (46) and the
insides of the two 10” Pads (45) with soapy water.
Slide a Pad about halfway up each Arm.
Insert a 7” Handle (47) with a Handgrip (48) into one
of the Arms (46). Attach the Handle with a 5/16” x
2 1/4” Bolt (33), two 5/16” Flat Washers (8), a 1/2” x
3/8” Spacer (51), and a 5/16” Nylon Locknut (3).
Attach a 7” Handle (47) with a Handgrip (48) to the
other Arm (46) in the same manner.
Press a 1” Round Inner Cap (49) into each 7”
Handle (47).
