Werner & Weber MPC-A Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

Werner & Weber MPC-A Скачать руководство пользователя страница 15

Page 14

issue january 2003

4. CARE and SERVICING

Waste compactors require very little servicing. However, compliance with the following instructions is
recom-mended to ensure failsafe operation and long machine life.

Conclusion of a service agreement is optional, yet recommended. Under such agreement, our service staff
will service your plant twice a year. Our specialists will identify potential problems hands-on, thus avoiding
major failures.

Service range:

1. inspection of hydraulic unit

2. adjustment (if required)

3. inspection of power unit

4. lubrication

5. filter cleaning

6. oil change (once a year))

7. overall inspection

DANGER

During all maintenance work, compliance with the following safety
instructions (also see chapter 1) is required:

1. Switch off main switch and padlock machine against unauthorized operation.

Remove key from padlock and keep it during maintenance.

2.

Push the EMERGENCY OFF button and disconnect supply mains from plug!

3.

Do not remove or deactivate protections!

4. Do not change setting of the hydraulic control unit (sealed). In case of replacement, original spare

parts suitable for an operating pressure of 250 bar must be used!

WERNER

WEBER

«
...
13
14
15
16
17
...
»

Содержание MPC-A





























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды