Wen LA3424 Скачать руководство пользователя

Страница: 6 / 24

WOOD LATHE SAFETY

1. This lathe is designed and intended for use by prop-

erly trained and experienced personnel only. If you are

not familiar with the proper and safe operation of a lathe,

do not use it until proper training and knowledge have

been acquired.

2. Always wear eye protection and a face shield/dust

mask when using the lathe.

3. Do not wear loose clothing or jewelry when using the

lathe. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewelry or long hair can be

caught in the spinning tool.

4. Select the right tool for your task at hand. Make sure

all tools, chisels and accessories are sharp before using

them. Do not use dull or damaged tools.

5. Select the appropriate speed for the task. Use slower

speeds when starting on a workpiece. Allow the lathe

to ramp up to the operating speed before engaging any

chisels, tools or other carving accessories.

6. Check the workpiece carefully for splits, knots, nails,

or other obstructions. These types of blemishes may

cause a safety hazards during turning.

7. If gluing up a workpiece for turning, always use a high

quality glue that meets the needs of the particular work-

piece to prevent the workpiece from falling off during

operation.

8. Cut the workpiece to a rough outline of the finished

shape before mounting it on the lathe.

9. Rotate the workpiece by hand to check clearance with

the tool rest before turning the machine on.

10. When turning between centers, make sure the head-

stock and tailstock are tight and snug against the work-

piece.

11. Never apply coolants or water to a spinning work-

piece.

12. Never stop a rotating workpiece with your hand.

13. Do not change speeds until the machine comes to a

complete stop.

14. Turn off and unplug the machine before doing any

cleaning or maintenance. Use a brush or compressed

air to remove chips or debris. Never use your hands to

remove excess material and debris.

These safety instructions can’t possibly warn of every

scenario that may arise with this tool, so always make

sure to stay alert and use common sense during op-

eration.

WOOD LATHE SAFETY WARNINGS

WARNING!

Do not operate the power tool until you have read and understood the following instructions and

the warning labels.

Содержание LA3424

























Результаты поиска

Содержание LA3424

Отзывы:

Похожие инструкции для LA3424

Бренды по названию

Популярные бренды

Wen LA3424, Инструкция по эксплуатации

Результаты поиска

Содержание LA3424

Отзывы:

Похожие инструкции для LA3424

Бренды по названию

Популярные бренды